Priyanka Jain 63310debc9 board/freescale: Remove P1024RDB board support 3 jaren geleden
..
Kconfig 63310debc9 board/freescale: Remove P1024RDB board support 3 jaren geleden
MAINTAINERS 63310debc9 board/freescale: Remove P1024RDB board support 3 jaren geleden
Makefile 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style 6 jaren geleden
README da3dd417d7 board/freescale: Remove P1020UTM board support 3 jaren geleden
ddr.c 6d1dd76afe board/freescale: Remove P1021RDB board support 3 jaren geleden
law.c 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style 6 jaren geleden
p1_p2_rdb_pc.c 6d1dd76afe board/freescale: Remove P1021RDB board support 3 jaren geleden
spl.c e516404ee5 powerpc: Remove bi_memstart & bi_memsize assignments in spl.c 3 jaren geleden
spl_minimal.c 941338725d common: Move relocate_code() to init.h 4 jaren geleden
tlb.c 53e3096cd0 board/freescale: Remove P1020MBG board support 3 jaren geleden

README

Overview
--------
P1_P2_RDB_PC represents a set of boards including
P1020MSBG-PC
P1020RDB-PC
P1020RDB-PD
P1021RDB-PC
P1024RDB
P2020RDB-PC

They have similar design of P1020RDB but have DDR3 instead of DDR2. P2020RDB-PC
has 64-bit DDR. All others have 32-bit DDR.

Key features on these boards include:
* DDR3
* NOR flash
* NAND flash (on RDB's only)
* SPI flash (on RDB's only)
* SDHC/MMC card slot
* VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
* PCIE slot and mini-PCIE slots

As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
is used to store SPD data. In case of absent or corrupted SPD, falling back
to timing data embedded in the source code will be used. Raw timing data is
extracted from DDR chip datasheet. Different speeds of DDR are supported with
this approach. ODT option is forced to fit this set of boards, again because
they don't have regular DIMMs.

CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet specification
for writing timing.

VSC firmware Address is defined by default in config file for eTSEC1.

SD width is based off DIP switch. DIP switch is detected on the
board by reading i2c bus and setting the appropriate mux values.

Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC have
pins multiplexing. QE function needs to be disabled to access Nor Flash and
CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below

'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.

Device tree support and how to enable it for different configs
--------------------------------------------------------------
Device tree support is available for p1020rdb and p2020rdb for below mentioned boot,
1. NOR Boot
2. NAND Boot
3. SD Boot
4. SPIFLASH Boot

To enable device tree support for other boot, below configs need to be
enabled in relative defconfig file,
1. CONFIG_DEFAULT_DEVICE_TREE="p1020rdb" (Change default device tree name if required)
2. CONFIG_OF_CONTROL
3. CONFIG_MPC85XX_HAVE_RESET_VECTOR if reset vector is located at
CONFIG_RESET_VECTOR_ADDRESS - 0xffc

If device tree support is enabled in defconfig,
1. use 'u-boot-with-dtb.bin' for NOR boot.
2. use 'u-boot-with-spl.bin' for other boot.