db-88f6281-bp.h 2.7 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293
  1. /* SPDX-License-Identifier: GPL-2.0+ */
  2. #ifndef _CONFIG_DB_88F6281_BP_H
  3. #define _CONFIG_DB_88F6281_BP_H
  4. /*
  5. * High Level Configuration Options (easy to change)
  6. */
  7. #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
  8. #define CONFIG_KW88F6281 1 /* SOC Name */
  9. #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
  10. #define CONFIG_SYS_TCLK 166666667
  11. #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
  12. #define CONFIG_BUILD_TARGET "u-boot.kwb"
  13. /* additions for new ARM relocation support */
  14. #define CONFIG_SYS_SDRAM_BASE 0x00000000
  15. #define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
  16. #define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */
  17. #define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
  18. #define CONFIG_KIRKWOOD_GPIO 1
  19. /*
  20. * NS16550 Configuration
  21. */
  22. #define CONFIG_SYS_NS16550_SERIAL
  23. #define CONFIG_SYS_NS16550_REG_SIZE (-4)
  24. #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
  25. #define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
  26. #define CONFIG_SYS_MAX_NAND_DEVICE 1
  27. /*
  28. * Serial Port configuration
  29. * The following definitions let you select what serial you want to use
  30. * for your console driver.
  31. */
  32. #define CONFIG_CONS_INDEX 1 /* Console on UART0 */
  33. /*
  34. * Environment variables configurations
  35. */
  36. #define CONFIG_ENV_SPI_BUS 0
  37. #define CONFIG_ENV_SPI_CS 0
  38. #define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */
  39. #define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
  40. /*
  41. * U-Boot bootcode configuration
  42. */
  43. #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */
  44. #define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */
  45. /*
  46. * For booting Linux, the board info and command line data
  47. * have to be in the first 8 MB of memory, since this is
  48. * the maximum mapped by the Linux kernel during initialization.
  49. */
  50. #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
  51. /* size in bytes reserved for initial data */
  52. #include <asm/arch/config.h>
  53. /* There is no PHY directly connected so don't ask it for link status */
  54. #undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  55. /*
  56. * Other required minimal configurations
  57. */
  58. #define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
  59. #define CONFIG_SYS_MEMTEST_END 0x007fffff /* (_8M - 1) */
  60. #define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
  61. /*
  62. * SDIO/MMC Card Configuration
  63. */
  64. #ifdef CONFIG_CMD_MMC
  65. #define CONFIG_MVEBU_MMC
  66. #define CONFIG_SYS_MMC_BASE KW_SDIO_BASE
  67. #endif /* CONFIG_CMD_MMC */
  68. /*
  69. * SATA Driver configuration
  70. */
  71. #ifdef CONFIG_MVSATA_IDE
  72. #define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
  73. #endif /*CONFIG_MVSATA_IDE*/
  74. #define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */
  75. #endif /* _CONFIG_DB_88F6281_BP_H */