123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293 |
- /* SPDX-License-Identifier: GPL-2.0+ */
- #ifndef _CONFIG_DB_88F6281_BP_H
- #define _CONFIG_DB_88F6281_BP_H
- /*
- * High Level Configuration Options (easy to change)
- */
- #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
- #define CONFIG_KW88F6281 1 /* SOC Name */
- #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
- #define CONFIG_SYS_TCLK 166666667
- #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
- #define CONFIG_BUILD_TARGET "u-boot.kwb"
- /* additions for new ARM relocation support */
- #define CONFIG_SYS_SDRAM_BASE 0x00000000
- #define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
- #define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */
- #define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
- #define CONFIG_KIRKWOOD_GPIO 1
- /*
- * NS16550 Configuration
- */
- #define CONFIG_SYS_NS16550_SERIAL
- #define CONFIG_SYS_NS16550_REG_SIZE (-4)
- #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
- #define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
- #define CONFIG_SYS_MAX_NAND_DEVICE 1
- /*
- * Serial Port configuration
- * The following definitions let you select what serial you want to use
- * for your console driver.
- */
- #define CONFIG_CONS_INDEX 1 /* Console on UART0 */
- /*
- * Environment variables configurations
- */
- #define CONFIG_ENV_SPI_BUS 0
- #define CONFIG_ENV_SPI_CS 0
- #define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */
- #define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
- /*
- * U-Boot bootcode configuration
- */
- #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */
- #define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */
- /*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
- #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
- /* size in bytes reserved for initial data */
- #include <asm/arch/config.h>
- /* There is no PHY directly connected so don't ask it for link status */
- #undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
- /*
- * Other required minimal configurations
- */
- #define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
- #define CONFIG_SYS_MEMTEST_END 0x007fffff /* (_8M - 1) */
- #define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
- /*
- * SDIO/MMC Card Configuration
- */
- #ifdef CONFIG_CMD_MMC
- #define CONFIG_MVEBU_MMC
- #define CONFIG_SYS_MMC_BASE KW_SDIO_BASE
- #endif /* CONFIG_CMD_MMC */
- /*
- * SATA Driver configuration
- */
- #ifdef CONFIG_MVSATA_IDE
- #define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
- #endif /*CONFIG_MVSATA_IDE*/
- #define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */
- #endif /* _CONFIG_DB_88F6281_BP_H */
|