|
@@ -19,7 +19,6 @@
|
|
|
#include <asm/gpio.h>
|
|
|
#include <asm/mach-imx/boot_mode.h>
|
|
|
#include <asm/mach-imx/sata.h>
|
|
|
-#include <asm/mach-imx/spi.h>
|
|
|
#include <asm/mach-imx/video.h>
|
|
|
#include <asm/io.h>
|
|
|
#include <asm/setup.h>
|
|
@@ -41,7 +40,6 @@
|
|
|
#include <power/pfuze100_pmic.h>
|
|
|
#include <fdt_support.h>
|
|
|
#include <jffs2/load_kernel.h>
|
|
|
-#include <spi_flash.h>
|
|
|
|
|
|
#include "gsc.h"
|
|
|
#include "common.h"
|
|
@@ -127,28 +125,6 @@ int board_ehci_hcd_init(int port)
|
|
|
}
|
|
|
#endif /* CONFIG_USB_EHCI_MX6 */
|
|
|
|
|
|
-#ifdef CONFIG_MXC_SPI
|
|
|
-iomux_v3_cfg_t const ecspi1_pads[] = {
|
|
|
- /* SS1 */
|
|
|
- IOMUX_PADS(PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(SPI_PAD_CTRL)),
|
|
|
- IOMUX_PADS(PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)),
|
|
|
- IOMUX_PADS(PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL)),
|
|
|
- IOMUX_PADS(PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)),
|
|
|
-};
|
|
|
-
|
|
|
-int board_spi_cs_gpio(unsigned bus, unsigned cs)
|
|
|
-{
|
|
|
- return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(3, 19)) : -1;
|
|
|
-}
|
|
|
-
|
|
|
-static void setup_spi(void)
|
|
|
-{
|
|
|
- gpio_request(IMX_GPIO_NR(3, 19), "spi_cs");
|
|
|
- gpio_direction_output(IMX_GPIO_NR(3, 19), 1);
|
|
|
- SETUP_IOMUX_PADS(ecspi1_pads);
|
|
|
-}
|
|
|
-#endif
|
|
|
-
|
|
|
/* configure eth0 PHY board-specific LED behavior */
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
|
{
|
|
@@ -591,9 +567,6 @@ int board_init(void)
|
|
|
setup_ventana_i2c(0);
|
|
|
board_type = read_eeprom(CONFIG_I2C_GSC, &ventana_info);
|
|
|
|
|
|
-#ifdef CONFIG_MXC_SPI
|
|
|
- setup_spi();
|
|
|
-#endif
|
|
|
setup_ventana_i2c(1);
|
|
|
setup_ventana_i2c(2);
|
|
|
|