|
@@ -1,453 +0,0 @@
|
|
|
-.. SPDX-License-Identifier: GPL-2.0+
|
|
|
-
|
|
|
-B4860QDS
|
|
|
-========
|
|
|
-
|
|
|
-The B4860QDS is a Freescale reference board that hosts the B4860 SoC
|
|
|
-(and variants).
|
|
|
-
|
|
|
-B4860 Overview
|
|
|
---------------
|
|
|
-The B4860 QorIQ Qonverge device is a Freescale high-end, multicore SoC based on
|
|
|
-StarCore and Power Architecture® cores. It targets the broadband wireless
|
|
|
-infrastructure and builds upon the proven success of the existing multicore
|
|
|
-DSPs and Power CPUs. It is designed to bolster the rapidly changing and
|
|
|
-expanding wireless markets, such as 3GLTE (FDD and TDD), LTE-Advanced, and UMTS.
|
|
|
-
|
|
|
-The B4860 is a highly-integrated StarCore and Power Architecture processor that
|
|
|
-contains:
|
|
|
-
|
|
|
-* Six fully-programmable StarCore SC3900 FVP subsystems, divided into three
|
|
|
- clusters-each core runs up to 1.2 GHz, with an architecture highly optimized
|
|
|
- for wireless base station applications
|
|
|
-* Four dual-thread e6500 Power Architecture processors organized in one
|
|
|
- cluster-each core runs up to 1.8 GHz
|
|
|
-* Two DDR3/3L controllers for high-speed, industry-standard memory interface
|
|
|
- each runs at up to 1866.67 MHz
|
|
|
-* MAPLE-B3 hardware acceleration-for forward error correction schemes including
|
|
|
- Turbo or Viterbi decoding, Turbo encoding and rate matching, MIMO MMSE
|
|
|
- equalization scheme, matrix operations, CRC insertion and check, DFT/iDFT and
|
|
|
- FFT/iFFT calculations, PUSCH/PDSCH acceleration, and UMTS chip rate
|
|
|
- acceleration
|
|
|
-* CoreNet fabric that fully supports coherency using MESI protocol between the
|
|
|
- e6500 cores, SC3900 FVP cores, memories and external interfaces.
|
|
|
- CoreNet fabric interconnect runs at 667 MHz and supports coherent and
|
|
|
- non-coherent out of order transactions with prioritization and bandwidth
|
|
|
- allocation amongst CoreNet endpoints.
|
|
|
-* Data Path Acceleration Architecture, which includes the following:
|
|
|
-
|
|
|
- * Frame Manager (FMan), which supports in-line packet parsing and general
|
|
|
- classification to enable policing and QoS-based packet distribution
|
|
|
- * Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading
|
|
|
- of queue management, task management, load distribution, flow ordering,
|
|
|
- buffer management, and allocation tasks from the cores
|
|
|
- * Security engine (SEC 5.3)-crypto-acceleration for protocols such as
|
|
|
- IPsec, SSL, and 802.16
|
|
|
- * RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound
|
|
|
- and outbound). Supports types 5, 6 (outbound only)
|
|
|
-
|
|
|
-* Large internal cache memory with snooping and stashing capabilities for
|
|
|
- bandwidth saving and high utilization of processor elements. The 9856-Kbyte
|
|
|
- internal memory space includes the following:
|
|
|
-
|
|
|
- * 32 Kbyte L1 ICache per e6500/SC3900 core
|
|
|
- * 32 Kbyte L1 DCache per e6500/SC3900 core
|
|
|
- * 2048 Kbyte unified L2 cache for each SC3900 FVP cluster
|
|
|
- * 2048 Kbyte unified L2 cache for the e6500 cluster
|
|
|
- * Two 512 Kbyte shared L3 CoreNet platform caches (CPC)
|
|
|
-
|
|
|
-* Sixteen 10-GHz SerDes lanes serving:
|
|
|
-
|
|
|
- * Two Serial RapidIO interfaces
|
|
|
- * Each supports up to 4 lanes and a total of up to 8 lanes
|
|
|
-
|
|
|
-* Up to 8-lanes Common Public Radio Interface (CPRI) controller for
|
|
|
- glue-less antenna connection
|
|
|
-* Two 10-Gbit Ethernet controllers (10GEC)
|
|
|
-* Six 1G/2.5-Gbit Ethernet controllers for network communications
|
|
|
-* PCI Express controller
|
|
|
-* Debug (Aurora)
|
|
|
-* Two OCeaN DMAs
|
|
|
-* Various system peripherals
|
|
|
-* 182 32-bit timers
|
|
|
-
|
|
|
-B4860QDS Overview
|
|
|
------------------
|
|
|
-- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
|
|
|
- ECC, 4 GB of memory in two ranks of 2 GB.
|
|
|
-- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
|
|
|
- ECC, 2 GB of memory. Single rank.
|
|
|
-- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
|
|
|
- 16x16 switch VSC3316
|
|
|
-- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
|
|
|
- 8x8 switch VSC3308
|
|
|
-- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
|
|
|
- B4860 UART port is available over USB-to-UART translator USB2SER or over
|
|
|
- RS232 flat cable.
|
|
|
-- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45
|
|
|
- copper connectors for Stand-alone mode and to the 1000Base-X over AMC
|
|
|
- MicroTCA connector ports 0 and 2 for AMC mode.
|
|
|
-- The B4860 configuration may be loaded from nine bits coded reset configuration
|
|
|
- reset source. The RCW source is set by appropriate DIP-switches.
|
|
|
-- 16-bit NOR Flash / PROMJet
|
|
|
-- QIXIS 8-bit NOR Flash Emulator
|
|
|
-- 8-bit NAND Flash
|
|
|
-- 24-bit SPI Flash
|
|
|
-- Long address I2C EEPROM
|
|
|
-- Available debug interfaces are:
|
|
|
-
|
|
|
- - On-board eCWTAP controller with ETH and USB I/F
|
|
|
- - JTAG/COP 16-pin header for any external TAP controller
|
|
|
- - External JTAG source over AMC to support B2B configuration
|
|
|
- - 70-pin Aurora debug connector
|
|
|
-
|
|
|
-- QIXIS (FPGA) logic:
|
|
|
- - 2 KB internal memory space including
|
|
|
-
|
|
|
-- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
|
|
|
- DDRCLK1,2 and RTCCLK.
|
|
|
-- Two 8T49N222A SerDes ref clock devices support two SerDes port clock
|
|
|
- frequency - total four refclk, including CPRI clock scheme.
|
|
|
-
|
|
|
-
|
|
|
-B4420 Personality
|
|
|
------------------
|
|
|
-
|
|
|
-B4420 is a reduced personality of B4860 with less core/clusters(both SC3900
|
|
|
-and e6500), less DDR controllers, less serdes lanes, less SGMII interfaces
|
|
|
-and reduced target frequencies.
|
|
|
-
|
|
|
-Key differences between B4860 and B4420
|
|
|
----------------------------------------
|
|
|
-
|
|
|
-B4420 has:
|
|
|
-
|
|
|
-1. Less e6500 cores: 1 cluster with 2 e6500 cores
|
|
|
-2. Less SC3900 cores/clusters: 1 cluster with 2 SC3900 cores per cluster
|
|
|
-3. Single DDRC
|
|
|
-4. 2X 4 lane serdes
|
|
|
-5. 3 SGMII interfaces
|
|
|
-6. no sRIO
|
|
|
-7. no 10G
|
|
|
-
|
|
|
-B4860QDS Default Settings
|
|
|
--------------------------
|
|
|
-
|
|
|
-Switch Settings
|
|
|
-^^^^^^^^^^^^^^^
|
|
|
-
|
|
|
-.. code-block:: none
|
|
|
-
|
|
|
- SW1 OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0]
|
|
|
- SW2 ON ON ON ON ON ON OFF OFF
|
|
|
- SW3 OFF OFF OFF ON OFF OFF ON OFF
|
|
|
- SW5 OFF OFF OFF OFF OFF OFF ON ON
|
|
|
-
|
|
|
-Note:
|
|
|
-
|
|
|
-- PCIe slots modes: All the PCIe devices work as Root Complex.
|
|
|
-- Boot location: NOR flash.
|
|
|
-
|
|
|
-SysClk/Core(e6500)/CCB/DDR/FMan/DDRCLK/StarCore/CPRI-Maple/eTVPE-Maple/ULB-Maple
|
|
|
-66MHz/1.6GHz/667MHz/1.6GHz data rate/667MHz/133MHz/1200MHz/500MHz/800MHz/667MHz
|
|
|
-
|
|
|
-NAND boot::
|
|
|
-
|
|
|
- SW1 [1.1] = 0
|
|
|
- SW2 [1.1] = 1
|
|
|
- SW3 [1:4] = 0001
|
|
|
-
|
|
|
-NOR boot::
|
|
|
-
|
|
|
- SW1 [1.1] = 1
|
|
|
- SW2 [1.1] = 0
|
|
|
- SW3 [1:4] = 1000
|
|
|
-
|
|
|
-B4420QDS Default Settings
|
|
|
--------------------------
|
|
|
-
|
|
|
-Switch Settings
|
|
|
-^^^^^^^^^^^^^^^
|
|
|
-
|
|
|
-.. code-block:: none
|
|
|
-
|
|
|
- SW1 OFF[0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0]
|
|
|
- SW2 ON OFF ON OFF ON ON OFF OFF
|
|
|
- SW3 OFF OFF OFF ON OFF OFF ON OFF
|
|
|
- SW5 OFF OFF OFF OFF OFF OFF ON ON
|
|
|
-
|
|
|
-Note:
|
|
|
-
|
|
|
-- PCIe slots modes: All the PCIe devices work as Root Complex.
|
|
|
-- Boot location: NOR flash.
|
|
|
-
|
|
|
-SysClk/Core(e6500)/CCB/DDR/FMan/DDRCLK/StarCore/CPRI-Maple/eTVPE-Maple/ULB-Maple
|
|
|
-66MHz/1.6GHz/667MHz/1.6GHz data rate/667MHz/133MHz/1200MHz/500MHz/800MHz/667MHz
|
|
|
-
|
|
|
-NAND boot::
|
|
|
-
|
|
|
- SW1 [1.1] = 0
|
|
|
- SW2 [1.1] = 1
|
|
|
- SW3 [1:4] = 0001
|
|
|
-
|
|
|
-NOR boot::
|
|
|
-
|
|
|
- SW1 [1.1] = 1
|
|
|
- SW2 [1.1] = 0
|
|
|
- SW3 [1:4] = 1000
|
|
|
-
|
|
|
-Memory map on B4860QDS
|
|
|
-----------------------
|
|
|
-The addresses in brackets are physical addresses.
|
|
|
-
|
|
|
-============= ============= =============== =======
|
|
|
-Start Address End Address Description Size
|
|
|
-============= ============= =============== =======
|
|
|
-0xF_FFDF_1000 0xF_FFFF_FFFF Free 2 MB
|
|
|
-0xF_FFDF_0000 0xF_FFDF_0FFF IFC - FPGA 4 KB
|
|
|
-0xF_FF81_0000 0xF_FFDE_FFFF Free 5 MB
|
|
|
-0xF_FF80_0000 0xF_FF80_FFFF IFC NAND Flash 64 KB
|
|
|
-0xF_FF00_0000 0xF_FF7F_FFFF Free 8 MB
|
|
|
-0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16 MB
|
|
|
-0xF_F801_0000 0xF_FDFF_FFFF Free 95 MB
|
|
|
-0xF_F800_0000 0xF_F800_FFFF PCIe I/O Space 64 KB
|
|
|
-0xF_F600_0000 0xF_F7FF_FFFF QMAN s/w portal 32 MB
|
|
|
-0xF_F400_0000 0xF_F5FF_FFFF BMAN s/w portal 32 MB
|
|
|
-0xF_F000_0000 0xF_F3FF_FFFF Free 64 MB
|
|
|
-0xF_E800_0000 0xF_EFFF_FFFF IFC NOR Flash 128 MB
|
|
|
-0xF_E000_0000 0xF_E7FF_FFFF Promjet 128 MB
|
|
|
-0xF_A0C0_0000 0xF_DFFF_FFFF Free 1012 MB
|
|
|
-0xF_A000_0000 0xF_A0BF_FFFF MAPLE0/1/2 12 MB
|
|
|
-0xF_0040_0000 0xF_9FFF_FFFF Free 12 GB
|
|
|
-0xF_0000_0000 0xF_01FF_FFFF DCSR 32 MB
|
|
|
-0xC_4000_0000 0xE_FFFF_FFFF Free 11 GB
|
|
|
-0xC_3000_0000 0xC_3FFF_FFFF sRIO-2 I/O 256 MB
|
|
|
-0xC_2000_0000 0xC_2FFF_FFFF sRIO-1 I/O 256 MB
|
|
|
-0xC_0000_0000 0xC_1FFF_FFFF PCIe Mem Space 512 MB
|
|
|
-0x1_0000_0000 0xB_FFFF_FFFF Free 44 GB
|
|
|
-0x0_8000_0000 0x0_FFFF_FFFF DDRC1 2 GB
|
|
|
-0x0_0000_0000 0x0_7FFF_FFFF DDRC2 2 GB
|
|
|
-============= ============= =============== =======
|
|
|
-
|
|
|
-Memory map on B4420QDS
|
|
|
-----------------------
|
|
|
-The addresses in brackets are physical addresses.
|
|
|
-
|
|
|
-============= ============= =============== =======
|
|
|
-Start Address End Address Description Size
|
|
|
-============= ============= =============== =======
|
|
|
-0xF_FFDF_1000 0xF_FFFF_FFFF Free 2 MB
|
|
|
-0xF_FFDF_0000 0xF_FFDF_0FFF IFC - FPGA 4 KB
|
|
|
-0xF_FF81_0000 0xF_FFDE_FFFF Free 5 MB
|
|
|
-0xF_FF80_0000 0xF_FF80_FFFF IFC NAND Flash 64 KB
|
|
|
-0xF_FF00_0000 0xF_FF7F_FFFF Free 8 MB
|
|
|
-0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16 MB
|
|
|
-0xF_F801_0000 0xF_FDFF_FFFF Free 95 MB
|
|
|
-0xF_F800_0000 0xF_F800_FFFF PCIe I/O Space 64 KB
|
|
|
-0xF_F600_0000 0xF_F7FF_FFFF QMAN s/w portal 32 MB
|
|
|
-0xF_F400_0000 0xF_F5FF_FFFF BMAN s/w portal 32 MB
|
|
|
-0xF_F000_0000 0xF_F3FF_FFFF Free 64 MB
|
|
|
-0xF_E800_0000 0xF_EFFF_FFFF IFC NOR Flash 128 MB
|
|
|
-0xF_E000_0000 0xF_E7FF_FFFF Promjet 128 MB
|
|
|
-0xF_A0C0_0000 0xF_DFFF_FFFF Free 1012 MB
|
|
|
-0xF_A000_0000 0xF_A0BF_FFFF MAPLE0/1/2 12 MB
|
|
|
-0xF_0040_0000 0xF_9FFF_FFFF Free 12 GB
|
|
|
-0xF_0000_0000 0xF_01FF_FFFF DCSR 32 MB
|
|
|
-0xC_4000_0000 0xE_FFFF_FFFF Free 11 GB
|
|
|
-0xC_3000_0000 0xC_3FFF_FFFF sRIO-2 I/O 256 MB
|
|
|
-0xC_2000_0000 0xC_2FFF_FFFF sRIO-1 I/O 256 MB
|
|
|
-0xC_0000_0000 0xC_1FFF_FFFF PCIe Mem Space 512 MB
|
|
|
-0x1_0000_0000 0xB_FFFF_FFFF Free 44 GB
|
|
|
-0x0_0000_0000 0x0_FFFF_FFFF DDRC1 4 GB
|
|
|
-============= ============= =============== =======
|
|
|
-
|
|
|
-NOR Flash memory Map on B4860 and B4420QDS
|
|
|
-------------------------------------------
|
|
|
-
|
|
|
-============= ============= ============================== =========
|
|
|
- Start End Definition Size
|
|
|
-============= ============= ============================== =========
|
|
|
-0xEFF40000 0xEFFFFFFF U-Boot (current bank) 768KB
|
|
|
-0xEFF20000 0xEFF3FFFF U-Boot env (current bank) 128KB
|
|
|
-0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB
|
|
|
-0xEF300000 0xEFEFFFFF rootfs (alternate bank) 12MB
|
|
|
-0xEE800000 0xEE8FFFFF device tree (alternate bank) 1MB
|
|
|
-0xEE020000 0xEE6FFFFF Linux.uImage (alternate bank) 6MB+896KB
|
|
|
-0xEE000000 0xEE01FFFF RCW (alternate bank) 128KB
|
|
|
-0xEDF40000 0xEDFFFFFF U-Boot (alternate bank) 768KB
|
|
|
-0xEDF20000 0xEDF3FFFF U-Boot env (alternate bank) 128KB
|
|
|
-0xEDF00000 0xEDF1FFFF FMAN ucode (alternate bank) 128KB
|
|
|
-0xED300000 0xEDEFFFFF rootfs (current bank) 12MB
|
|
|
-0xEC800000 0xEC8FFFFF device tree (current bank) 1MB
|
|
|
-0xEC020000 0xEC6FFFFF Linux.uImage (current bank) 6MB+896KB
|
|
|
-0xEC000000 0xEC01FFFF RCW (current bank) 128KB
|
|
|
-============= ============= ============================== =========
|
|
|
-
|
|
|
-Various Software configurations/environment variables/commands
|
|
|
---------------------------------------------------------------
|
|
|
-The below commands apply to both B4860QDS and B4420QDS.
|
|
|
-
|
|
|
-U-Boot environment variable hwconfig
|
|
|
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
-
|
|
|
-The default hwconfig is:
|
|
|
-
|
|
|
-.. code-block:: none
|
|
|
-
|
|
|
- hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1:dr_mode=host,phy_type=ulpi
|
|
|
-
|
|
|
-Note: For USB gadget set "dr_mode=peripheral"
|
|
|
-
|
|
|
-FMAN Ucode versions
|
|
|
-^^^^^^^^^^^^^^^^^^^
|
|
|
-
|
|
|
-fsl_fman_ucode_B4860_106_3_6.bin
|
|
|
-
|
|
|
-Switching to alternate bank
|
|
|
-^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
-
|
|
|
-Commands for switching to alternate bank.
|
|
|
-
|
|
|
-1. To change from vbank0 to vbank2
|
|
|
-
|
|
|
-.. code-block:: none
|
|
|
-
|
|
|
- => qixis_reset altbank (it will boot using vbank2)
|
|
|
-
|
|
|
-2. To change from vbank2 to vbank0
|
|
|
-
|
|
|
-.. code-block:: none
|
|
|
-
|
|
|
- => qixis reset (it will boot using vbank0)
|
|
|
-
|
|
|
-To change personality of board
|
|
|
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
-
|
|
|
-For changing personality from B4860 to B4420
|
|
|
-
|
|
|
-1. Boot from vbank0
|
|
|
-2. Flash vbank2 with b4420 rcw and U-Boot
|
|
|
-3. Give following commands to uboot prompt
|
|
|
-
|
|
|
-.. code-block:: none
|
|
|
-
|
|
|
- => mw.b ffdf0040 0x30;
|
|
|
- => mw.b ffdf0010 0x00;
|
|
|
- => mw.b ffdf0062 0x02;
|
|
|
- => mw.b ffdf0050 0x02;
|
|
|
- => mw.b ffdf0010 0x30;
|
|
|
- => reset
|
|
|
-
|
|
|
-Note:
|
|
|
-
|
|
|
-- Power off cycle will lead to default switch settings.
|
|
|
-- 0xffdf0000 is the address of the QIXIS FPGA.
|
|
|
-
|
|
|
-Switching between NOR and NAND boot(RCW src changed from NOR <-> NAND)
|
|
|
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
-
|
|
|
-To change from NOR to NAND boot give following command on uboot prompt
|
|
|
-
|
|
|
-.. code-block:: none
|
|
|
-
|
|
|
- => mw.b ffdf0040 0x30
|
|
|
- => mw.b ffdf0010 0x00
|
|
|
- => mw.b 0xffdf0050 0x08
|
|
|
- => mw.b 0xffdf0060 0x82
|
|
|
- => mw.b ffdf0061 0x00
|
|
|
- => mw.b ffdf0010 0x30
|
|
|
- => reset
|
|
|
-
|
|
|
-To change from NAND to NOR boot give following command on uboot prompt:
|
|
|
-
|
|
|
-.. code-block:: none
|
|
|
-
|
|
|
- => mw.b ffdf0040 0x30
|
|
|
- => mw.b ffdf0010 0x00
|
|
|
- => mw.b 0xffdf0050 0x00(for vbank0) or (mw.b 0xffdf0050 0x02 for vbank2)
|
|
|
- => mw.b 0xffdf0060 0x12
|
|
|
- => mw.b ffdf0061 0x01
|
|
|
- => mw.b ffdf0010 0x30
|
|
|
- => reset
|
|
|
-
|
|
|
-Note:
|
|
|
-
|
|
|
-- Power off cycle will lead to default switch settings.
|
|
|
-- 0xffdf0000 is the address of the QIXIS FPGA.
|
|
|
-
|
|
|
-Ethernet interfaces for B4860QDS
|
|
|
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
-
|
|
|
-Serdes protocosl tested:
|
|
|
-* 0x2a, 0x8d (serdes1, serdes2) [DEFAULT]
|
|
|
-* 0x2a, 0xb2 (serdes1, serdes2)
|
|
|
-
|
|
|
-When using [DEFAULT] RCW, which including 2 * 1G SGMII on board and 2 * 1G
|
|
|
-SGMII on SGMII riser card.
|
|
|
-
|
|
|
-Under U-Boot these network interfaces are recognized as::
|
|
|
-
|
|
|
- FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5 and FM1@DTSEC6.
|
|
|
-
|
|
|
-On Linux the interfaces are renamed as::
|
|
|
-
|
|
|
- eth2 -> fm1-gb2
|
|
|
- eth3 -> fm1-gb3
|
|
|
- eth4 -> fm1-gb4
|
|
|
- eth5 -> fm1-gb5
|
|
|
-
|
|
|
-RCW and Ethernet interfaces for B4420QDS
|
|
|
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
-
|
|
|
-Serdes protocosl tested:
|
|
|
-* 0x18, 0x9e (serdes1, serdes2)
|
|
|
-
|
|
|
-Under U-Boot these network interfaces are recognized as::
|
|
|
-
|
|
|
- FM1@DTSEC3, FM1@DTSEC4 and e1000#0.
|
|
|
-
|
|
|
-On Linux the interfaces are renamed as::
|
|
|
-
|
|
|
- eth2 -> fm1-gb2
|
|
|
- eth3 -> fm1-gb3
|
|
|
-
|
|
|
-NAND boot with 2 Stage boot loader
|
|
|
-----------------------------------
|
|
|
-PBL initialise the internal SRAM and copy SPL(160KB) in SRAM.
|
|
|
-SPL further initialise DDR using SPD and environment variables and copy
|
|
|
-U-Boot(768 KB) from flash to DDR.
|
|
|
-Finally SPL transer control to U-Boot for futher booting.
|
|
|
-
|
|
|
-SPL has following features:
|
|
|
- - Executes within 256K
|
|
|
- - No relocation required
|
|
|
-
|
|
|
-Run time view of SPL framework during boot:
|
|
|
-
|
|
|
-+----------------------------------------------+
|
|
|
-|Area | Address |
|
|
|
-+----------------------------------------------+
|
|
|
-|Secure boot | 0xFFFC0000 (32KB) |
|
|
|
-|headers | |
|
|
|
-+----------------------------------------------+
|
|
|
-|GD, BD | 0xFFFC8000 (4KB) |
|
|
|
-+----------------------------------------------+
|
|
|
-|ENV | 0xFFFC9000 (8KB) |
|
|
|
-+----------------------------------------------+
|
|
|
-|HEAP | 0xFFFCB000 (30KB) |
|
|
|
-+----------------------------------------------+
|
|
|
-|STACK | 0xFFFD8000 (22KB) |
|
|
|
-+----------------------------------------------+
|
|
|
-|U-Boot SPL | 0xFFFD8000 (160KB) |
|
|
|
-+----------------------------------------------+
|
|
|
-
|
|
|
-NAND Flash memory Map on B4860 and B4420QDS
|
|
|
--------------------------------------------
|
|
|
-
|
|
|
-============= ============= ============================= =====
|
|
|
-Start End Definition Size
|
|
|
-============= ============= ============================= =====
|
|
|
-0x000000 0x0FFFFF U-Boot 1MB
|
|
|
-0x140000 0x15FFFF U-Boot env 128KB
|
|
|
-0x1A0000 0x1BFFFF FMAN Ucode 128KB
|
|
|
-============= ============= ============================= =====
|