|
@@ -5,11 +5,15 @@
|
|
|
|
|
|
#include <common.h>
|
|
|
#include <dm.h>
|
|
|
+#include <env.h>
|
|
|
#include <log.h>
|
|
|
-#include <power/regulator.h>
|
|
|
#include <spl_gpio.h>
|
|
|
#include <asm/io.h>
|
|
|
+#include <power/regulator.h>
|
|
|
+
|
|
|
+#include <asm/arch-rockchip/cru.h>
|
|
|
#include <asm/arch-rockchip/gpio.h>
|
|
|
+#include <asm/arch-rockchip/grf_rk3399.h>
|
|
|
|
|
|
#ifndef CONFIG_SPL_BUILD
|
|
|
int board_early_init_f(void)
|
|
@@ -32,13 +36,43 @@ out:
|
|
|
|
|
|
#else
|
|
|
|
|
|
+#define PMUGRF_BASE 0xff320000
|
|
|
#define GPIO0_BASE 0xff720000
|
|
|
|
|
|
+/**
|
|
|
+ * LED setup for roc-rk3399-pc
|
|
|
+ *
|
|
|
+ * 1. Set the low power leds (only during POR, pwr_key env is 'y')
|
|
|
+ * glow yellow LED, termed as low power
|
|
|
+ * poll for on board power key press
|
|
|
+ * once powe key pressed, turn off yellow
|
|
|
+ * 2. Turn on red LED, indicating full power mode
|
|
|
+ */
|
|
|
void led_setup(void)
|
|
|
{
|
|
|
struct rockchip_gpio_regs * const gpio0 = (void *)GPIO0_BASE;
|
|
|
+ struct rk3399_pmugrf_regs * const pmugrf = (void *)PMUGRF_BASE;
|
|
|
+ bool press_pwr_key = false;
|
|
|
+
|
|
|
+ if (IS_ENABLED(CONFIG_SPL_ENV_SUPPORT)) {
|
|
|
+ env_init();
|
|
|
+ env_load();
|
|
|
+ if (env_get_yesno("pwr_key") == 1)
|
|
|
+ press_pwr_key = true;
|
|
|
+ }
|
|
|
+
|
|
|
+ if (press_pwr_key && !strcmp(get_reset_cause(), "POR")) {
|
|
|
+ spl_gpio_output(gpio0, GPIO(BANK_A, 2), 1);
|
|
|
+
|
|
|
+ spl_gpio_set_pull(&pmugrf->gpio0_p, GPIO(BANK_A, 5),
|
|
|
+ GPIO_PULL_NORMAL);
|
|
|
+ while (readl(&gpio0->ext_port) & 0x20)
|
|
|
+ ;
|
|
|
+
|
|
|
+ spl_gpio_output(gpio0, GPIO(BANK_A, 2), 0);
|
|
|
+ }
|
|
|
|
|
|
- /* Turn on red LED, indicating full power mode */
|
|
|
spl_gpio_output(gpio0, GPIO(BANK_B, 5), 1);
|
|
|
}
|
|
|
+
|
|
|
#endif
|