Преглед изворни кода

configs/arcturus_ucp1020: bump Linux and U-Boot

Bump Linux and U-Boot versions.

The Linux configuration file and patches are no longer needed.

Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
[Thomas: also use a tarball for U-Boot.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Oleksandr Zhadan пре 4 година
родитељ
комит
42a172bb0e

+ 0 - 269
board/arcturus/ppc-ucp1020/configs/linux-4.1.x.config

@@ -1,269 +0,0 @@
-CONFIG_PPC_85xx=y
-CONFIG_SMP=y
-CONFIG_NR_CPUS=2
-CONFIG_CROSS_COMPILE="powerpc-linux-"
-CONFIG_LOCALVERSION="-ANI-uCP1020-64EE512"
-# CONFIG_LOCALVERSION_AUTO is not set
-CONFIG_DEFAULT_HOSTNAME="uCP1020-64EE512"
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_AUDIT=y
-CONFIG_NO_HZ_IDLE=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_LOG_CPU_MAX_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED=y
-CONFIG_BLK_DEV_INITRD=y
-# CONFIG_RD_BZIP2 is not set
-# CONFIG_RD_LZMA is not set
-# CONFIG_RD_XZ is not set
-# CONFIG_RD_LZO is not set
-# CONFIG_RD_LZ4 is not set
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_EMBEDDED=y
-# CONFIG_SLUB_DEBUG is not set
-# CONFIG_COMPAT_BRK is not set
-CONFIG_JUMP_LABEL=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_MAC_PARTITION=y
-# CONFIG_EFI_PARTITION is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_UCP1020_SOM=y
-CONFIG_HIGHMEM=y
-CONFIG_PREEMPT=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_MATH_EMULATION=y
-CONFIG_MATH_EMULATION_HW_UNIMPLEMENTED=y
-CONFIG_SWIOTLB=y
-# CONFIG_COMPACTION is not set
-CONFIG_PCI=y
-CONFIG_PCIEPORTBUS=y
-# CONFIG_PCIEAER is not set
-# CONFIG_PCIEASPM is not set
-CONFIG_PCI_MSI=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_XFRM_USER=y
-CONFIG_NET_KEY=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_SYN_COOKIES=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_IPV6 is not set
-CONFIG_NETFILTER=y
-CONFIG_BRIDGE_NETFILTER=y
-CONFIG_NF_CONNTRACK=y
-CONFIG_NF_CONNTRACK_FTP=y
-CONFIG_NETFILTER_XT_TARGET_CONNMARK=y
-CONFIG_NETFILTER_XT_TARGET_MARK=y
-CONFIG_NETFILTER_XT_MATCH_COMMENT=y
-CONFIG_NETFILTER_XT_MATCH_CONNMARK=y
-CONFIG_NETFILTER_XT_MATCH_CONNTRACK=y
-CONFIG_NETFILTER_XT_MATCH_HELPER=y
-CONFIG_NETFILTER_XT_MATCH_MARK=y
-CONFIG_NETFILTER_XT_MATCH_MULTIPORT=y
-CONFIG_NETFILTER_XT_MATCH_STATE=y
-CONFIG_NF_CONNTRACK_IPV4=y
-CONFIG_IP_NF_IPTABLES=y
-CONFIG_IP_NF_FILTER=y
-CONFIG_IP_NF_TARGET_REJECT=y
-CONFIG_IP_NF_NAT=y
-CONFIG_IP_NF_TARGET_MASQUERADE=y
-CONFIG_IP_NF_TARGET_NETMAP=y
-CONFIG_IP_NF_TARGET_REDIRECT=y
-CONFIG_IP_NF_MANGLE=y
-CONFIG_BRIDGE=y
-CONFIG_VLAN_8021Q=y
-CONFIG_NET_SCHED=y
-CONFIG_NET_SCH_HTB=y
-CONFIG_CFG80211=y
-# CONFIG_CFG80211_DEFAULT_PS is not set
-CONFIG_MAC80211=y
-# CONFIG_MAC80211_RC_MINSTREL is not set
-CONFIG_UEVENT_HELPER_PATH="/bin/hotplug"
-CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_FTL=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_PHYSMAP_OF=y
-CONFIG_MTD_M25P80=y
-CONFIG_MTD_SST25L=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_PLATFORM=y
-CONFIG_MTD_NAND_FSL_ELBC=y
-CONFIG_MTD_NAND_FSL_UPM=y
-CONFIG_MTD_SPI_NOR=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=131072
-CONFIG_EEPROM_AT25=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_CHR_DEV_ST=y
-CONFIG_BLK_DEV_SR=y
-CONFIG_CHR_DEV_SG=y
-CONFIG_SCSI_LOGGING=y
-CONFIG_NETDEVICES=y
-# CONFIG_NET_VENDOR_3COM is not set
-# CONFIG_NET_VENDOR_ADAPTEC is not set
-# CONFIG_NET_VENDOR_AGERE is not set
-# CONFIG_NET_VENDOR_ALTEON is not set
-# CONFIG_NET_VENDOR_AMD is not set
-# CONFIG_NET_VENDOR_ARC is not set
-# CONFIG_NET_VENDOR_ATHEROS is not set
-# CONFIG_NET_CADENCE is not set
-# CONFIG_NET_VENDOR_BROADCOM is not set
-# CONFIG_NET_VENDOR_BROCADE is not set
-# CONFIG_NET_VENDOR_CHELSIO is not set
-# CONFIG_NET_VENDOR_CISCO is not set
-# CONFIG_NET_VENDOR_DEC is not set
-# CONFIG_NET_VENDOR_DLINK is not set
-# CONFIG_NET_VENDOR_EMULEX is not set
-# CONFIG_NET_VENDOR_EXAR is not set
-CONFIG_GIANFAR=y
-# CONFIG_NET_VENDOR_HP is not set
-# CONFIG_NET_VENDOR_INTEL is not set
-# CONFIG_NET_VENDOR_MARVELL is not set
-# CONFIG_NET_VENDOR_MELLANOX is not set
-# CONFIG_NET_VENDOR_MICREL is not set
-# CONFIG_NET_VENDOR_MICROCHIP is not set
-# CONFIG_NET_VENDOR_MYRI is not set
-# CONFIG_NET_VENDOR_NATSEMI is not set
-# CONFIG_NET_VENDOR_NVIDIA is not set
-# CONFIG_NET_VENDOR_OKI is not set
-# CONFIG_NET_PACKET_ENGINE is not set
-# CONFIG_NET_VENDOR_QLOGIC is not set
-# CONFIG_NET_VENDOR_QUALCOMM is not set
-# CONFIG_NET_VENDOR_REALTEK is not set
-# CONFIG_NET_VENDOR_RDC is not set
-# CONFIG_NET_VENDOR_ROCKER is not set
-# CONFIG_NET_VENDOR_SAMSUNG is not set
-# CONFIG_NET_VENDOR_SEEQ is not set
-# CONFIG_NET_VENDOR_SILAN is not set
-# CONFIG_NET_VENDOR_SIS is not set
-# CONFIG_NET_VENDOR_SMSC is not set
-# CONFIG_NET_VENDOR_STMICRO is not set
-# CONFIG_NET_VENDOR_SUN is not set
-# CONFIG_NET_VENDOR_TEHUTI is not set
-# CONFIG_NET_VENDOR_TI is not set
-# CONFIG_NET_VENDOR_VIA is not set
-# CONFIG_NET_VENDOR_WIZNET is not set
-# CONFIG_NET_VENDOR_XILINX is not set
-CONFIG_MICREL_PHY=y
-CONFIG_IWLWIFI=m
-# CONFIG_INPUT_MOUSEDEV is not set
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_SERIO_LIBPS2=y
-CONFIG_LEGACY_PTY_COUNT=16
-CONFIG_NOZOMI=y
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=2
-CONFIG_SERIAL_8250_RUNTIME_UARTS=2
-CONFIG_SERIAL_8250_MANY_PORTS=y
-CONFIG_SERIAL_8250_DETECT_IRQ=y
-CONFIG_SERIAL_8250_RSA=y
-CONFIG_NVRAM=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_MPC=y
-CONFIG_SPI=y
-CONFIG_SPI_BITBANG=y
-CONFIG_SPI_FSL_ESPI=y
-CONFIG_SPI_SPIDEV=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_MPC8XXX=y
-CONFIG_SENSORS_LM90=y
-CONFIG_THERMAL=y
-CONFIG_WATCHDOG=y
-CONFIG_BOOKE_WDT=y
-CONFIG_BOOKE_WDT_DEFAULT_TIMEOUT=36
-CONFIG_MEDIA_SUPPORT=y
-CONFIG_MEDIA_CAMERA_SUPPORT=y
-CONFIG_MEDIA_CONTROLLER=y
-CONFIG_VIDEO_V4L2_SUBDEV_API=y
-CONFIG_MEDIA_USB_SUPPORT=y
-CONFIG_USB_VIDEO_CLASS=y
-CONFIG_USB_GSPCA=y
-CONFIG_USB_PWC=y
-CONFIG_USB_ZR364XX=y
-CONFIG_USB_STKWEBCAM=y
-CONFIG_VIDEO_EM28XX=y
-CONFIG_VIDEO_EM28XX_V4L2=y
-# CONFIG_HID is not set
-# CONFIG_USB_HID is not set
-CONFIG_USB=y
-CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_DYNAMIC_MINORS=y
-CONFIG_USB_MON=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_EHCI_FSL=y
-CONFIG_USB_ACM=y
-CONFIG_USB_WDM=y
-CONFIG_USB_TMC=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_STORAGE_DEBUG=y
-CONFIG_USB_MDC800=y
-CONFIG_MMC=y
-CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_PLTFM=y
-CONFIG_MMC_SDHCI_OF_ESDHC=y
-CONFIG_DMADEVICES=y
-CONFIG_FSL_DMA=y
-CONFIG_ASYNC_TX_DMA=y
-# CONFIG_IOMMU_SUPPORT is not set
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
-# CONFIG_EXT3_FS_XATTR is not set
-CONFIG_EXT4_FS=y
-CONFIG_XFS_FS=y
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_NTFS_FS=y
-CONFIG_PROC_KCORE=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_JFFS2_FS_WBUF_VERIFY=y
-CONFIG_JFFS2_SUMMARY=y
-CONFIG_JFFS2_FS_XATTR=y
-CONFIG_JFFS2_COMPRESSION_OPTIONS=y
-CONFIG_JFFS2_LZO=y
-CONFIG_JFFS2_RUBIN=y
-CONFIG_CRAMFS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V4=y
-CONFIG_NFSD=y
-CONFIG_CIFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_CRC_T10DIF=y
-CONFIG_CRC_ITU_T=y
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_RCU_CPU_STALL_TIMEOUT=60
-# CONFIG_RCU_CPU_STALL_INFO is not set
-# CONFIG_FTRACE is not set
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_PCBC=y
-CONFIG_CRYPTO_SHA1=y
-CONFIG_CRYPTO_SHA1_PPC=y
-CONFIG_CRYPTO_DEFLATE=y
-# CONFIG_CRYPTO_ANSI_CPRNG is not set
-CONFIG_CRYPTO_DEV_TALITOS=y

+ 0 - 462
board/arcturus/ppc-ucp1020/patches/linux/0001-Arcturus-uCP1020-BSP-support.patch

@@ -1,462 +0,0 @@
-From a243628639e12a4bd0a737eac78a12ed240cd137 Mon Sep 17 00:00:00 2001
-From: Oleksandr G Zhadan <oleks@arcturusnetworks.com>
-Date: Mon, 18 Jul 2016 10:40:16 -0400
-Subject: [PATCH] Arcturus uCP1020 BSP support
-
-The uCP1020 product family (ucp1020) is an Arcturus Networks Inc.
-System on Modules product featuring a NXP QorIQ P1020 CPU,
-optionally populated with 1 or 2 Gig-Ethernet PHYs,
-DDR3, NOR Flash, eMMC NAND Flash and/or SPI Flash.
-
-Signed-off-by: Oleksandr G Zhadan <oleks@arcturusnetworks.com>
-Signed-off-by: Michael Durrant <arcsupport@arcturusnetworks.com>
----
- arch/powerpc/boot/dts/ucp1020.dts         |  87 ++++++++++++
- arch/powerpc/boot/dts/ucp1020.dtsi        | 211 ++++++++++++++++++++++++++++++
- arch/powerpc/platforms/85xx/Kconfig       |   7 +
- arch/powerpc/platforms/85xx/Makefile      |   1 +
- arch/powerpc/platforms/85xx/ucp1020_som.c |  92 +++++++++++++
- 5 files changed, 398 insertions(+)
- create mode 100644 arch/powerpc/boot/dts/ucp1020.dts
- create mode 100644 arch/powerpc/boot/dts/ucp1020.dtsi
- create mode 100644 arch/powerpc/platforms/85xx/ucp1020_som.c
-
-diff --git a/arch/powerpc/boot/dts/ucp1020.dts b/arch/powerpc/boot/dts/ucp1020.dts
-new file mode 100644
-index 0000000..291e70a
---- /dev/null
-+++ b/arch/powerpc/boot/dts/ucp1020.dts
-@@ -0,0 +1,87 @@
-+/*
-+ * uCP1020 Tree Source (32-bit address map)
-+ *
-+ * Copyright 2013-2016 Arcturus Networks Inc.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions are met:
-+ *     * Redistributions of source code must retain the above copyright
-+ *       notice, this list of conditions and the following disclaimer.
-+ *     * Redistributions in binary form must reproduce the above copyright
-+ *       notice, this list of conditions and the following disclaimer in the
-+ *       documentation and/or other materials provided with the distribution.
-+ *     * Neither the name of Freescale Semiconductor nor the
-+ *       names of its contributors may be used to endorse or promote products
-+ *       derived from this software without specific prior written permission.
-+ *
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") as published by the Free Software
-+ * Foundation, either version 2 of that License or (at your option) any
-+ * later version.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
-+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
-+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
-+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
-+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
-+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+/include/ "fsl/p1020si-pre.dtsi"
-+/ {
-+	model = "arcturus,uCP1020";
-+	compatible = "arcturus,uCP1020";
-+
-+	memory {
-+		device_type = "memory";
-+	};
-+
-+	lbc: localbus@ffe05000 {
-+		reg = <0 0xffe05000 0 0x1000>;
-+
-+		/* NOR Flash */
-+		ranges = <0x0 0x0 0x0 0xec000000 0x04000000>;
-+	};
-+
-+	soc: soc@ffe00000 {
-+		ranges = <0x0 0x0 0xffe00000 0x100000>;
-+	};
-+
-+	pci0: pcie@ffe09000 {
-+		ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
-+			  0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
-+		reg = <0 0xffe09000 0 0x1000>;
-+		pcie@0 {
-+			ranges = <0x2000000 0x0 0xa0000000
-+				  0x2000000 0x0 0xa0000000
-+				  0x0 0x20000000
-+
-+				  0x1000000 0x0 0x0
-+				  0x1000000 0x0 0x0
-+				  0x0 0x100000>;
-+		};
-+	};
-+
-+	pci1: pcie@ffe0a000 {
-+		reg = <0 0xffe0a000 0 0x1000>;
-+		ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
-+			  0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
-+		pcie@0 {
-+			ranges = <0x2000000 0x0 0x80000000
-+				  0x2000000 0x0 0x80000000
-+				  0x0 0x20000000
-+
-+				  0x1000000 0x0 0x0
-+				  0x1000000 0x0 0x0
-+				  0x0 0x100000>;
-+		};
-+	};
-+};
-+
-+/include/ "ucp1020.dtsi"
-+/include/ "fsl/p1020si-post.dtsi"
-diff --git a/arch/powerpc/boot/dts/ucp1020.dtsi b/arch/powerpc/boot/dts/ucp1020.dtsi
-new file mode 100644
-index 0000000..7cff949
---- /dev/null
-+++ b/arch/powerpc/boot/dts/ucp1020.dtsi
-@@ -0,0 +1,211 @@
-+/*
-+ * uCP1020 Device Tree Source stub (no addresses or top-level ranges)
-+ *
-+ * Copyright 2013-2016 Arcturus Networks Inc.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions are met:
-+ *     * Redistributions of source code must retain the above copyright
-+ *       notice, this list of conditions and the following disclaimer.
-+ *     * Redistributions in binary form must reproduce the above copyright
-+ *       notice, this list of conditions and the following disclaimer in the
-+ *       documentation and/or other materials provided with the distribution.
-+ *     * Neither the name of Freescale Semiconductor nor the
-+ *       names of its contributors may be used to endorse or promote products
-+ *       derived from this software without specific prior written permission.
-+ *
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") as published by the Free Software
-+ * Foundation, either version 2 of that License or (at your option) any
-+ * later version.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
-+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
-+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
-+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
-+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
-+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+&lbc {
-+	nor@0,0 {
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+		compatible = "cfi-flash";
-+		reg = <0x0 0x0 0x04000000>;
-+		bank-width = <2>;
-+		device-width = <1>;
-+
-+		partition@100000 {
-+			/* 7MB - PART 0 */
-+			reg = <0x00100000 0x00700000>;
-+			label = "0";
-+		};
-+
-+		partition@800000 {
-+			/* 32MB - PART 1 */
-+			reg = <0x0800000 0x02000000>;
-+			label = "1";
-+		};
-+
-+		partition@2800000 {
-+			/* 8MB - PART 2 */
-+			reg = <0x02800000 0x00800000>;
-+			label = "2";
-+		};
-+
-+		partition@3000000 {
-+			/* (16MB - 512K) - PART 3 JFFS 2 */
-+			reg = <0x03000000 0x00f80000>;
-+			label = "3";
-+		};
-+
-+		partition@0 {
-+			/* 512KB - bootloader[u-boot, uCbootloader] */
-+			reg = <0x0 0x00080000>;
-+			label = "BOOT_SPI";
-+		};
-+
-+		partition@3f80000 {
-+			/* 512KB - bootloade NOR r[u-boot, uCbootloader] */
-+			reg = <0x03f80000 0x00080000>;
-+			label = "B";
-+		};
-+
-+		partition@80000 {
-+			/* 256KB - bootloaders environment (uCenv) */
-+			reg = <0x00080000 0x00040000>;
-+	
-+			label = "E";
-+		};
-+
-+		partition@C0000 {
-+			/* 256KB - bootloaders environment (u-boot) */
-+			reg = <0x000C0000 0x00040000>;
-+			label = "UENV";
-+		};
-+	};
-+};
-+
-+&soc {
-+	i2c@3000 {
-+		spoc@14 {
-+			compatible = "conexant,cx2070x";
-+			reg = <0x14>;
-+		};
-+	};
-+
-+	i2c@3100 {
-+			dtt@4C {
-+				compatible = "national,lm90";
-+				reg = <0x4C>;
-+			};
-+	};
-+
-+	spi@7000 {
-+		flash@0 {
-+			#address-cells = <1>;
-+			#size-cells = <1>;
-+			compatible = "winbond,w25q80bl";
-+			reg = <0>;
-+			spi-max-frequency = <40000000>; /* input clock */
-+
-+			partition@0 {
-+				label = "SPI MBR";
-+				reg = <0x00000000 0x00002000>;
-+				read-only;
-+			};
-+			partition@2000 {
-+				label = "SPI ENV";
-+				reg = <0x00002000 0x00006000>;
-+				read-only;
-+			};
-+			partition@8000 {
-+				label = "SPI FS";
-+				reg = <0x00008000 0x000F8000>;
-+			};
-+		};
-+		flash@3 {
-+			#address-cells = <1>;
-+			#size-cells = <1>;
-+			compatible = "spansion,s25fl008k";
-+			reg = <3>;
-+			spi-max-frequency = <40000000>; /* input clock */
-+			partition@0 {
-+				label = "SPI USER";
-+				reg = <0x00000000 0x00100000>;
-+			};
-+		};
-+	};
-+
-+	usb@22000 {
-+		phy_type = "ulpi";
-+		dr_mode = "host";
-+	};
-+
-+	mdio@24000 {
-+		phy0: ethernet-phy@4 {
-+			interrupt-parent = <&mpic>;
-+			interrupts = <4 1>;
-+			reg = <0x04>;
-+		};
-+
-+		phy1: ethernet-phy@6 {
-+			interrupt-parent = <&mpic>;
-+			interrupts = <8 1>;
-+			reg = <0x6>;
-+		};
-+	};
-+
-+	enet0: ethernet@b0000 {
-+		phy-handle = <&phy0>;
-+		phy-connection-type = "rgmii-id";
-+	};
-+
-+	enet1: ethernet@b1000 {
-+		status = "disabled";
-+	};
-+
-+	enet2: ethernet@b2000 {
-+		phy-handle = <&phy1>;
-+		phy-connection-type = "rgmii-id";
-+	};
-+
-+	gpio0: gpio@f000 {
-+		compatible = "fsl,mpc8572-gpio", "fsl,pq3-gpio";
-+		reg = <0xf000 0x1000>;
-+		interrupts = <47 2>;
-+		interrupt-parent = <&mpic>;
-+		#gpio-cells = <2>;
-+		gpio-controller;
-+	};
-+
-+	gpio-leds {
-+		compatible = "gpio-leds";
-+		gpio5 {
-+			label = "led1";		/* LED15 */
-+			gpios = <&gpio0 5 0>;
-+		};
-+		gpio12 {
-+			label = "led2";		/* LED16 */
-+			gpios = <&gpio0 12 0>;
-+		};
-+		gpio13 {
-+			label = "led3";		/* LED17 */
-+			gpios = <&gpio0 13 0>;
-+		};
-+		gpio7 {
-+			label = "led4";		/* LED18 */
-+			gpios = <&gpio0 7 0>;
-+		};
-+		gpio6 {
-+			label = "led5";		/* LED19 */
-+			gpios = <&gpio0 6 0>;
-+		};
-+	};
-+};
-diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
-index 2fb4b24..81a944f 100644
---- a/arch/powerpc/platforms/85xx/Kconfig
-+++ b/arch/powerpc/platforms/85xx/Kconfig
-@@ -241,6 +241,13 @@ config SGY_CTS1000
- 	help
- 	  Enable this to support functionality in Servergy's CTS-1000 systems.
- 
-+config UCP1020_SOM
-+	bool "Arcturus uCP1020 Rev.1.3 System on Module"
-+	select DEFAULT_UIMAGE
-+	help
-+	  This option enables support for the Arcturus Networks Inc. 
-+	  uCP1020 System on Module.
-+
- config MVME2500
- 	bool "Artesyn MVME2500"
- 	select DEFAULT_UIMAGE
-diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile
-index 1fe7fb9..84f2b9a 100644
---- a/arch/powerpc/platforms/85xx/Makefile
-+++ b/arch/powerpc/platforms/85xx/Makefile
-@@ -31,4 +31,5 @@ obj-$(CONFIG_XES_MPC85xx) += xes_mpc85xx.o
- obj-$(CONFIG_GE_IMP3A)	  += ge_imp3a.o
- obj-$(CONFIG_PPC_QEMU_E500) += qemu_e500.o
- obj-$(CONFIG_SGY_CTS1000) += sgy_cts1000.o
-+obj-$(CONFIG_UCP1020_SOM) += ucp1020_som.o
- obj-$(CONFIG_MVME2500)	  += mvme2500.o
-diff --git a/arch/powerpc/platforms/85xx/ucp1020_som.c b/arch/powerpc/platforms/85xx/ucp1020_som.c
-new file mode 100644
-index 0000000..777e8ad
---- /dev/null
-+++ b/arch/powerpc/platforms/85xx/ucp1020_som.c
-@@ -0,0 +1,92 @@
-+/*
-+ * Arcturus Networks Inc. uCP1020 module Setup
-+ *
-+ * Copyright 2014-2016 Arcturus Networks Inc.
-+ *
-+ * by Oleksandr G Zhadan & Michael Durrant (www.ArcturusNetworks.com)
-+ *
-+ * This program is free software; you can redistribute  it and/or modify it
-+ * under  the terms of  the GNU General  Public License as published by the
-+ * Free Software Foundation;  either version 2 of the  License, or (at your
-+ * option) any later version.
-+ */
-+
-+#include <linux/stddef.h>
-+#include <linux/kernel.h>
-+#include <linux/pci.h>
-+#include <linux/kdev_t.h>
-+#include <linux/delay.h>
-+#include <linux/seq_file.h>
-+#include <linux/interrupt.h>
-+#include <linux/of_platform.h>
-+
-+#include <asm/time.h>
-+#include <asm/machdep.h>
-+#include <asm/pci-bridge.h>
-+#include <mm/mmu_decl.h>
-+#include <asm/prom.h>
-+#include <asm/udbg.h>
-+#include <asm/mpic.h>
-+#include <asm/fsl_guts.h>
-+
-+#include <sysdev/fsl_soc.h>
-+#include <sysdev/fsl_pci.h>
-+#include "smp.h"
-+
-+#include "mpc85xx.h"
-+
-+void __init ucp1020_som_pic_init(void)
-+{
-+	struct mpic *mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN |
-+	  MPIC_SINGLE_DEST_CPU,
-+	  0, 256, " OpenPIC  ");
-+
-+	BUG_ON(mpic == NULL);
-+
-+	mpic_init(mpic);
-+}
-+
-+/*
-+ * Setup the architecture
-+ */
-+static void __init ucp1020_som_setup_arch(void)
-+{
-+	if (ppc_md.progress)
-+		ppc_md.progress("uCP1020_SoM_setup_arch()", 0);
-+
-+	mpc85xx_smp_init();
-+
-+	fsl_pci_assign_primary();
-+	pr_info("\n\t%s (http://www.arcturusnetworks.com)\n", ppc_md.name);
-+}
-+
-+machine_arch_initcall(ucp1020, mpc85xx_common_publish_devices);
-+machine_arch_initcall(ucp1020, swiotlb_setup_bus_notifier);
-+
-+/*
-+ * Called very early, device-tree isn't unflattened
-+ */
-+static int __init ucp1020_probe(void)
-+{
-+	unsigned long root = of_get_flat_dt_root();
-+
-+	if (of_flat_dt_is_compatible(root, "arcturus,uCP1020"))
-+		return 1;
-+	return 0;
-+}
-+
-+define_machine(ucp1020) {
-+	.name			= "uCP1020 SoM - Arcturus Networks Inc.",
-+	.probe			= ucp1020_probe,
-+	.setup_arch		= ucp1020_som_setup_arch,
-+	.init_IRQ		= ucp1020_som_pic_init,
-+#ifdef CONFIG_PCI
-+	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
-+#endif
-+	.get_irq		= mpic_get_irq,
-+	.restart		= fsl_rstcr_restart,
-+	.calibrate_decr		= generic_calibrate_decr,
-+#ifdef DEBUG 
-+	.progress		= udbg_progress,
-+#endif
-+};
--- 
-2.1.4
-

+ 0 - 28
board/arcturus/ppc-ucp1020/patches/linux/0002-p1020-esdhc-controller-reserved-bit.patch

@@ -1,28 +0,0 @@
-From 4c74fd1266287deca0c1ff091071c5b8558b9735 Mon Sep 17 00:00:00 2001
-From: Oleksandr G Zhadan <oleks@arcturusnetworks.com>
-Date: Mon, 18 Jul 2016 10:45:41 -0400
-Subject: [PATCH 1/1] p1020 esdhc controller reserved bit
-
-Prevent SDHCI core from writing reserved bits, where
-p1020 reserved bit is SDHCI_CTRL_HISPD, not 0x01(SDHCI_CTRL_LED).
-
-Signed-off-by: Oleksandr G Zhadan <oleks@arcturusnetworks.com>
-Signed-off-by: Michael Durrant <arcsupport@arcturusnetworks.com>
----
- drivers/mmc/host/sdhci-esdhc.h | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
-diff --git a/drivers/mmc/host/sdhci-esdhc.h b/drivers/mmc/host/sdhci-esdhc.h
-index a870c42..b45de0a 100644
---- a/drivers/mmc/host/sdhci-esdhc.h
-+++ b/drivers/mmc/host/sdhci-esdhc.h
-@@ -45,6 +45,6 @@
- #define ESDHC_DMA_SYSCTL	0x40c
- #define ESDHC_DMA_SNOOP		0x00000040
- 
--#define ESDHC_HOST_CONTROL_RES	0x01
-+#define ESDHC_HOST_CONTROL_RES	(SDHCI_CTRL_HISPD)
- 
- #endif /* _DRIVERS_MMC_SDHCI_ESDHC_H */
--- 
-2.1.4

+ 0 - 53
board/arcturus/ppc-ucp1020/patches/linux/0003-powerpc-ptrace-Fix-out-of-bounds-array-access-warning.patch

@@ -1,53 +0,0 @@
-From 35b7ce4f8f290794d3b89db7461e8c568b5defa1 Mon Sep 17 00:00:00 2001
-From: Khem Raj <raj.khem@gmail.com>
-Date: Mon, 25 Apr 2016 09:19:17 -0700
-Subject: powerpc/ptrace: Fix out of bounds array access warning
-
-commit 1e407ee3b21f981140491d5b8a36422979ca246f upstream.
-
-gcc-6 correctly warns about a out of bounds access
-
-arch/powerpc/kernel/ptrace.c:407:24: warning: index 32 denotes an offset greater than size of 'u64[32][1] {aka long long unsigned int[32][1]}' [-Warray-bounds]
-        offsetof(struct thread_fp_state, fpr[32][0]));
-                        ^
-
-check the end of array instead of beginning of next element to fix this
-
-Signed-off-by: Khem Raj <raj.khem@gmail.com>
-Cc: Kees Cook <keescook@chromium.org>
-Cc: Michael Ellerman <mpe@ellerman.id.au>
-Cc: Segher Boessenkool <segher@kernel.crashing.org>
-Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
-Acked-by: Olof Johansson <olof@lixom.net>
-Cc: Arnd Bergmann <arnd@arndb.de>
-Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
-Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
----
- arch/powerpc/kernel/ptrace.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
-diff --git a/arch/powerpc/kernel/ptrace.c b/arch/powerpc/kernel/ptrace.c
-index f21897b..93f200f 100644
---- a/arch/powerpc/kernel/ptrace.c
-+++ b/arch/powerpc/kernel/ptrace.c
-@@ -376,7 +376,7 @@ static int fpr_get(struct task_struct *target, const struct user_regset *regset,
- 
- #else
- 	BUILD_BUG_ON(offsetof(struct thread_fp_state, fpscr) !=
--		     offsetof(struct thread_fp_state, fpr[32][0]));
-+		     offsetof(struct thread_fp_state, fpr[32]));
- 
- 	return user_regset_copyout(&pos, &count, &kbuf, &ubuf,
- 				   &target->thread.fp_state, 0, -1);
-@@ -404,7 +404,7 @@ static int fpr_set(struct task_struct *target, const struct user_regset *regset,
- 	return 0;
- #else
- 	BUILD_BUG_ON(offsetof(struct thread_fp_state, fpscr) !=
--		     offsetof(struct thread_fp_state, fpr[32][0]));
-+		     offsetof(struct thread_fp_state, fpr[32]));
- 
- 	return user_regset_copyin(&pos, &count, &kbuf, &ubuf,
- 				  &target->thread.fp_state, 0, -1);
--- 
-cgit v1.1

+ 1 - 0
board/arcturus/ppc-ucp1020/readme.txt

@@ -38,6 +38,7 @@ You'll need to program the files created by buildroot into the NOR flash.
     B$ protect off 0xeff80000 +$filesize
     B$ erase 0xeff80000 +$filesize
     B$ cp.b $loadaddr 0xeff80000 $filesize
+    B$ protect on 0xeff80000 +$filesize
 
 2. Program the kernel
 

+ 9 - 10
configs/arcturus_ucp1020_defconfig

@@ -2,8 +2,8 @@
 BR2_powerpc=y
 BR2_powerpc_8548=y
 
-# Linux headers same as kernel, a 4.1 series
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+# Linux headers same as kernel, a 4.4 series
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_4=y
 
 # System settings
 BR2_TARGET_GENERIC_HOSTNAME="UCP1020"
@@ -13,11 +13,9 @@ BR2_SYSTEM_DHCP="eth0"
 
 # Kernel
 BR2_LINUX_KERNEL=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.27"
-BR2_LINUX_KERNEL_PATCH="board/arcturus/ppc-ucp1020/patches/linux"
-BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/arcturus/ppc-ucp1020/configs/linux-4.1.x.config"
+BR2_LINUX_KERNEL_CUSTOM_TARBALL=y
+BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call github,ArcturusNetworks,uCP1020-kernel,v20190618)/linux-v20190618.tar.gz"
+BR2_LINUX_KERNEL_DEFCONFIG="ucp1020"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="ucp1020"
 
@@ -26,6 +24,7 @@ BR2_TARGET_ROOTFS_JFFS2=y
 
 # U-boot
 BR2_TARGET_UBOOT=y
-BR2_TARGET_UBOOT_BOARDNAME="UCP1020"
-BR2_TARGET_UBOOT_CUSTOM_VERSION=y
-BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2016.07"
+BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
+BR2_TARGET_UBOOT_CUSTOM_TARBALL=y
+BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call github,ArcturusNetworks,uCP1020-uboot,v20190618)/uboot-v20190618.tar.gz"
+BR2_TARGET_UBOOT_BOARD_DEFCONFIG="UCP1020"