SBx81LIFKW.h 3.2 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101
  1. /* SPDX-License-Identifier: GPL-2.0+ */
  2. /*
  3. * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz>
  4. */
  5. #ifndef _CONFIG_SBX81LIFKW_H
  6. #define _CONFIG_SBX81LIFKW_H
  7. /*
  8. * High Level Configuration Options (easy to change)
  9. */
  10. #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
  11. #define CONFIG_KW88F6281 1 /* SOC Name */
  12. #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
  13. #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
  14. /* additions for new ARM relocation support */
  15. #define CONFIG_SYS_SDRAM_BASE 0x00000000
  16. #define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
  17. #define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
  18. #define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */
  19. #define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
  20. #define CONFIG_KIRKWOOD_GPIO 1
  21. /*
  22. * NS16550 Configuration
  23. */
  24. #define CONFIG_SYS_NS16550
  25. #define CONFIG_SYS_NS16550_SERIAL
  26. #define CONFIG_SYS_NS16550_REG_SIZE (-4)
  27. #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
  28. #define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
  29. /*
  30. * Serial Port configuration
  31. * The following definitions let you select what serial you want to use
  32. * for your console driver.
  33. */
  34. #define CONFIG_CONS_INDEX 1 /*Console on UART0 */
  35. /*
  36. * For booting Linux, the board info and command line data
  37. * have to be in the first 8 MB of memory, since this is
  38. * the maximum mapped by the Linux kernel during initialization.
  39. */
  40. #define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
  41. #define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
  42. #define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
  43. #define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
  44. #define MTDPARTS_MTDOOPS "errlog"
  45. #define CONFIG_DOS_PARTITION
  46. /*
  47. * Environment variables configurations
  48. */
  49. /*
  50. * U-Boot bootcode configuration
  51. */
  52. #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */
  53. #define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */
  54. /*
  55. * For booting Linux, the board info and command line data
  56. * have to be in the first 8 MB of memory, since this is
  57. * the maximum mapped by the Linux kernel during initialization.
  58. */
  59. #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
  60. /* size in bytes reserved for initial data */
  61. #include <asm/arch/config.h>
  62. /* There is no PHY directly connected so don't ask it for link status */
  63. #undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  64. /*
  65. * Other required minimal configurations
  66. */
  67. #define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
  68. #define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
  69. #define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
  70. /*
  71. * Ethernet Driver configuration
  72. */
  73. #ifdef CONFIG_CMD_NET
  74. #define CONFIG_NETCONSOLE /* include NetConsole support */
  75. #define CONFIG_NET_MULTI /* specify more that one ports available */
  76. #define CONFIG_MVGBE /* Enable kirkwood Gbe Controller Driver */
  77. #define CONFIG_MVGBE_PORTS {1, 0} /* enable a single port */
  78. #define CONFIG_PHY_BASE_ADR 0x01
  79. #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
  80. #endif /* CONFIG_CMD_NET */
  81. #define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */
  82. #endif /* _CONFIG_SBX81LIFKW_H */