work_92105.h 3.0 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138
  1. /* SPDX-License-Identifier: GPL-2.0+ */
  2. /*
  3. * WORK Microwave work_92105 board configuration file
  4. *
  5. * (C) Copyright 2014 DENX Software Engineering GmbH
  6. * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
  7. */
  8. #ifndef __CONFIG_WORK_92105_H__
  9. #define __CONFIG_WORK_92105_H__
  10. /* SoC and board defines */
  11. #include <linux/sizes.h>
  12. #include <asm/arch/cpu.h>
  13. /*
  14. * Define work_92105 machine type by hand -- done only for compatibility
  15. * with original board code
  16. */
  17. #define CONFIG_MACH_TYPE 736
  18. #if !defined(CONFIG_SPL_BUILD)
  19. #define CONFIG_SKIP_LOWLEVEL_INIT
  20. #endif
  21. /*
  22. * Memory configurations
  23. */
  24. #define CONFIG_SYS_MALLOC_LEN SZ_1M
  25. #define CONFIG_SYS_SDRAM_BASE EMC_DYCS0_BASE
  26. #define CONFIG_SYS_SDRAM_SIZE SZ_128M
  27. #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_32K)
  28. #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_512K \
  29. - GENERATED_GBL_DATA_SIZE)
  30. /*
  31. * Ethernet Driver
  32. */
  33. #define CONFIG_LPC32XX_ETH
  34. #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  35. /* FIXME: remove "Waiting for PHY auto negotiation to complete..." message */
  36. /*
  37. * I2C driver
  38. */
  39. #define CONFIG_SYS_I2C_LPC32XX
  40. #define CONFIG_SYS_I2C
  41. #define CONFIG_SYS_I2C_SPEED 350000
  42. /*
  43. * I2C EEPROM
  44. */
  45. #define CONFIG_SYS_I2C_EEPROM_ADDR 0x56
  46. #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
  47. /*
  48. * I2C RTC
  49. */
  50. #define CONFIG_RTC_DS1374
  51. /*
  52. * U-Boot General Configurations
  53. */
  54. #define CONFIG_SYS_CBSIZE 1024
  55. #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
  56. /*
  57. * NAND chip timings for FIXME: which one?
  58. */
  59. #define CONFIG_LPC32XX_NAND_MLC_TCEA_DELAY 333333333
  60. #define CONFIG_LPC32XX_NAND_MLC_BUSY_DELAY 10000000
  61. #define CONFIG_LPC32XX_NAND_MLC_NAND_TA 18181818
  62. #define CONFIG_LPC32XX_NAND_MLC_RD_HIGH 31250000
  63. #define CONFIG_LPC32XX_NAND_MLC_RD_LOW 45454545
  64. #define CONFIG_LPC32XX_NAND_MLC_WR_HIGH 40000000
  65. #define CONFIG_LPC32XX_NAND_MLC_WR_LOW 83333333
  66. /*
  67. * NAND
  68. */
  69. /* driver configuration */
  70. #define CONFIG_SYS_NAND_SELF_INIT
  71. #define CONFIG_SYS_MAX_NAND_DEVICE 1
  72. #define CONFIG_SYS_MAX_NAND_CHIPS 1
  73. #define CONFIG_SYS_NAND_BASE MLC_NAND_BASE
  74. #define CONFIG_NAND_LPC32XX_MLC
  75. /*
  76. * GPIO
  77. */
  78. #define CONFIG_LPC32XX_GPIO
  79. /*
  80. * Environment
  81. */
  82. /*
  83. * Boot Linux
  84. */
  85. #define CONFIG_CMDLINE_TAG
  86. #define CONFIG_SETUP_MEMORY_TAGS
  87. #define CONFIG_INITRD_TAG
  88. #define CONFIG_BOOTFILE "uImage"
  89. #define CONFIG_LOADADDR 0x80008000
  90. /*
  91. * SPL
  92. */
  93. /* SPL will be executed at offset 0 */
  94. /* SPL will use SRAM as stack */
  95. #define CONFIG_SPL_STACK 0x0000FFF8
  96. /* Use the framework and generic lib */
  97. /* SPL will use serial */
  98. /* SPL will load U-Boot from NAND offset 0x40000 */
  99. #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x00040000
  100. #define CONFIG_SPL_PAD_TO 0x20000
  101. /* U-Boot will be 0x40000 bytes, loaded and run at CONFIG_SYS_TEXT_BASE */
  102. #define CONFIG_SYS_MONITOR_LEN 0x40000 /* actually, MAX size */
  103. #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
  104. #define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE
  105. /*
  106. * Include SoC specific configuration
  107. */
  108. #include <asm/arch/config.h>
  109. #endif /* __CONFIG_WORK_92105_H__*/