|
@@ -565,11 +565,6 @@ The following options need to be configured:
|
|
|
boards with QUICC Engines require OF_QE to set UCC MAC
|
|
|
addresses
|
|
|
|
|
|
- CONFIG_OF_BOARD_SETUP
|
|
|
-
|
|
|
- Board code has addition modification that it wants to make
|
|
|
- to the flat device tree before handing it off to the kernel
|
|
|
-
|
|
|
CONFIG_OF_SYSTEM_SETUP
|
|
|
|
|
|
Other code has addition modification that it wants to make
|
|
@@ -596,9 +591,6 @@ The following options need to be configured:
|
|
|
Note: If a "bootargs" environment is defined, it will override
|
|
|
the defaults discussed just above.
|
|
|
|
|
|
-- Cache Configuration:
|
|
|
- CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
|
|
|
-
|
|
|
- Cache Configuration for ARM:
|
|
|
CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
|
|
|
controller
|
|
@@ -1520,16 +1512,6 @@ The following options need to be configured:
|
|
|
SPI EEPROM, also an instance works with Crystal A/D and
|
|
|
D/As on the SACSng board)
|
|
|
|
|
|
- CONFIG_SOFT_SPI
|
|
|
-
|
|
|
- Enables a software (bit-bang) SPI driver rather than
|
|
|
- using hardware support. This is a general purpose
|
|
|
- driver that only requires three general I/O port pins
|
|
|
- (two outputs, one input) to function. If this is
|
|
|
- defined, the board configuration must define several
|
|
|
- SPI configuration items (port pins to use, etc). For
|
|
|
- an example, see include/configs/sacsng.h.
|
|
|
-
|
|
|
CONFIG_SYS_SPI_MXC_WAIT
|
|
|
Timeout for waiting until spi transfer completed.
|
|
|
default: (CONFIG_SYS_HZ/100) /* 10 ms */
|
|
@@ -1595,13 +1577,6 @@ The following options need to be configured:
|
|
|
Time to wait after FPGA configuration. The default is
|
|
|
200 ms.
|
|
|
|
|
|
-- Configuration Management:
|
|
|
-
|
|
|
- CONFIG_IDENT_STRING
|
|
|
-
|
|
|
- If defined, this string will be added to the U-Boot
|
|
|
- version information (U_BOOT_VERSION)
|
|
|
-
|
|
|
- Vendor Parameter Protection:
|
|
|
|
|
|
U-Boot considers the values of the environment
|
|
@@ -1922,10 +1897,6 @@ The following options need to be configured:
|
|
|
CONFIG_SPL_INIT_MINIMAL
|
|
|
Arch init code should be built for a very small image
|
|
|
|
|
|
- CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
|
|
|
- Partition on the MMC to load U-Boot from when the MMC is being
|
|
|
- used in raw mode
|
|
|
-
|
|
|
CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
|
|
|
Sector to load kernel uImage from when MMC is being
|
|
|
used in raw mode (for Falcon mode)
|