Browse Source

spl: make SPL and normal u-boot stage use independent SYS_MALLOC_F_LEN

Some platforms have very limited SRAM to run SPL code, so there may
not be the same amount space for a malloc pool before relocation in
the SPL stage as the normal U-Boot stage.

Make SPL and (the full) U-Boot stage use independent SYS_MALLOC_F_LEN,
so the size of pre-relocation malloc pool can be configured memory
space independently.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[fixed up commit-message:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Andy Yan 6 years ago
parent
commit
f1896c45cb

+ 10 - 0
Kconfig

@@ -95,6 +95,16 @@ config SYS_MALLOC_F_LEN
 	  particular needs this to operate, so that it can allocate the
 	  initial serial device and any others that are needed.
 
+config SPL_SYS_MALLOC_F_LEN
+        hex "Size of malloc() pool in spl before relocation"
+        depends on SYS_MALLOC_F
+        default SYS_MALLOC_F_LEN
+        help
+          Before relocation, memory is very limited on many platforms. Still,
+          we can provide a small malloc() pool if needed. Driver model in
+          particular needs this to operate, so that it can allocate the
+          initial serial device and any others that are needed.
+
 menuconfig EXPERT
 	bool "Configure standard U-Boot features (expert users)"
 	default y

+ 2 - 2
cmd/bdinfo.c

@@ -344,9 +344,9 @@ static int do_bdinfo(cmd_tbl_t *cmdtp, int flag, int argc,
 #ifdef CONFIG_BOARD_TYPES
 	printf("Board Type  = %ld\n", gd->board_type);
 #endif
-#ifdef CONFIG_SYS_MALLOC_F
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
 	printf("Early malloc usage: %lx / %x\n", gd->malloc_ptr,
-	       CONFIG_SYS_MALLOC_F_LEN);
+	       CONFIG_VAL(SYS_MALLOC_F_LEN));
 #endif
 	if (gd->fdt_blob)
 		printf("fdt_blob = %p\n", gd->fdt_blob);

+ 3 - 1
common/Makefile

@@ -139,9 +139,11 @@ obj-y += console.o
 endif
 obj-$(CONFIG_CROS_EC) += cros_ec.o
 obj-y += dlmalloc.o
-ifdef CONFIG_SYS_MALLOC_F_LEN
+ifdef CONFIG_SYS_MALLOC_F
+ifneq ($(CONFIG_$(SPL_)SYS_MALLOC_F_LEN),0)
 obj-y += malloc_simple.o
 endif
+endif
 obj-y += image.o
 obj-$(CONFIG_ANDROID_BOOT_IMAGE) += image-android.o
 obj-$(CONFIG_$(SPL_)OF_LIBFDT) += image-fdt.o

+ 2 - 2
common/board_f.c

@@ -727,7 +727,7 @@ static int initf_bootstage(void)
 
 static int initf_console_record(void)
 {
-#if defined(CONFIG_CONSOLE_RECORD) && defined(CONFIG_SYS_MALLOC_F_LEN)
+#if defined(CONFIG_CONSOLE_RECORD) && CONFIG_VAL(SYS_MALLOC_F_LEN)
 	return console_record_init();
 #else
 	return 0;
@@ -736,7 +736,7 @@ static int initf_console_record(void)
 
 static int initf_dm(void)
 {
-#if defined(CONFIG_DM) && defined(CONFIG_SYS_MALLOC_F_LEN)
+#if defined(CONFIG_DM) && CONFIG_VAL(SYS_MALLOC_F_LEN)
 	int ret;
 
 	bootstage_start(BOOTSTATE_ID_ACCUM_DM_F, "dm_f");

+ 1 - 1
common/board_r.c

@@ -256,7 +256,7 @@ static int initr_malloc(void)
 {
 	ulong malloc_start;
 
-#ifdef CONFIG_SYS_MALLOC_F_LEN
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
 	debug("Pre-reloc malloc() used %#lx bytes (%ld KB)\n", gd->malloc_ptr,
 	      gd->malloc_ptr / 1024);
 #endif

+ 6 - 6
common/dlmalloc.c

@@ -1254,7 +1254,7 @@ Void_t* mALLOc(bytes) size_t bytes;
 
   INTERNAL_SIZE_T nb;
 
-#ifdef CONFIG_SYS_MALLOC_F_LEN
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
 	if (!(gd->flags & GD_FLG_FULL_MALLOC_INIT))
 		return malloc_simple(bytes);
 #endif
@@ -1522,7 +1522,7 @@ void fREe(mem) Void_t* mem;
   mchunkptr fwd;       /* misc temp for linking */
   int       islr;      /* track whether merging with last_remainder */
 
-#ifdef CONFIG_SYS_MALLOC_F_LEN
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
 	/* free() is a no-op - all the memory will be freed on relocation */
 	if (!(gd->flags & GD_FLG_FULL_MALLOC_INIT))
 		return;
@@ -1679,7 +1679,7 @@ Void_t* rEALLOc(oldmem, bytes) Void_t* oldmem; size_t bytes;
   /* realloc of null is supposed to be same as malloc */
   if (oldmem == NULL) return mALLOc(bytes);
 
-#ifdef CONFIG_SYS_MALLOC_F_LEN
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
 	if (!(gd->flags & GD_FLG_FULL_MALLOC_INIT)) {
 		/* This is harder to support and should not be needed */
 		panic("pre-reloc realloc() is not supported");
@@ -2074,7 +2074,7 @@ Void_t* cALLOc(n, elem_size) size_t n; size_t elem_size;
     return NULL;
   else
   {
-#ifdef CONFIG_SYS_MALLOC_F_LEN
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
 	if (!(gd->flags & GD_FLG_FULL_MALLOC_INIT)) {
 		MALLOC_ZERO(mem, sz);
 		return mem;
@@ -2375,9 +2375,9 @@ int mALLOPt(param_number, value) int param_number; int value;
 
 int initf_malloc(void)
 {
-#ifdef CONFIG_SYS_MALLOC_F_LEN
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
 	assert(gd->malloc_base);	/* Set up by crt0.S */
-	gd->malloc_limit = CONFIG_SYS_MALLOC_F_LEN;
+	gd->malloc_limit = CONFIG_VAL(SYS_MALLOC_F_LEN);
 	gd->malloc_ptr = 0;
 #endif
 

+ 4 - 4
common/init/board_init.c

@@ -46,8 +46,8 @@ __weak void arch_setup_gd(struct global_data *gd_ptr)
 ulong board_init_f_alloc_reserve(ulong top)
 {
 	/* Reserve early malloc arena */
-#if defined(CONFIG_SYS_MALLOC_F)
-	top -= CONFIG_SYS_MALLOC_F_LEN;
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
+	top -= CONFIG_VAL(SYS_MALLOC_F_LEN);
 #endif
 	/* LAST : reserve GD (rounded up to a multiple of 16 bytes) */
 	top = rounddown(top-sizeof(struct global_data), 16);
@@ -121,11 +121,11 @@ void board_init_f_init_reserve(ulong base)
 	 * Use gd as it is now properly set for all architectures.
 	 */
 
-#if defined(CONFIG_SYS_MALLOC_F)
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
 	/* go down one 'early malloc arena' */
 	gd->malloc_base = base;
 	/* next alloc will be higher by one 'early malloc arena' size */
-	base += CONFIG_SYS_MALLOC_F_LEN;
+	base += CONFIG_VAL(SYS_MALLOC_F_LEN);
 #endif
 }
 

+ 4 - 4
common/spl/spl.c

@@ -220,12 +220,12 @@ static int spl_common_init(bool setup_malloc)
 
 	debug("spl_early_init()\n");
 
-#if defined(CONFIG_SYS_MALLOC_F_LEN)
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
 	if (setup_malloc) {
 #ifdef CONFIG_MALLOC_F_ADDR
 		gd->malloc_base = CONFIG_MALLOC_F_ADDR;
 #endif
-		gd->malloc_limit = CONFIG_SYS_MALLOC_F_LEN;
+		gd->malloc_limit = CONFIG_VAL(SYS_MALLOC_F_LEN);
 		gd->malloc_ptr = 0;
 	}
 #endif
@@ -419,7 +419,7 @@ void board_init_r(gd_t *dummy1, ulong dummy2)
 	default:
 		debug("Unsupported OS image.. Jumping nevertheless..\n");
 	}
-#if defined(CONFIG_SYS_MALLOC_F_LEN) && !defined(CONFIG_SYS_SPL_MALLOC_SIZE)
+#if CONFIG_VAL(SYS_MALLOC_F_LEN) && !defined(CONFIG_SYS_SPL_MALLOC_SIZE)
 	debug("SPL malloc() used %#lx bytes (%ld KB)\n", gd->malloc_ptr,
 	      gd->malloc_ptr / 1024);
 #endif
@@ -486,7 +486,7 @@ ulong spl_relocate_stack_gd(void)
 	gd_t *new_gd;
 	ulong ptr = CONFIG_SPL_STACK_R_ADDR;
 
-#ifdef CONFIG_SPL_SYS_MALLOC_SIMPLE
+#if defined(CONFIG_SPL_SYS_MALLOC_SIMPLE) && CONFIG_SPL_SYS_MALLOC_F_LEN
 	if (CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN) {
 		ptr -= CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN;
 		gd->malloc_base = ptr;

+ 4 - 4
drivers/core/Kconfig

@@ -16,10 +16,10 @@ config SPL_DM
 	  suitable malloc() implementation. If you are not using the
 	  full malloc() enabled by CONFIG_SYS_SPL_MALLOC_START,
 	  consider using CONFIG_SYS_MALLOC_SIMPLE. In that case you
-	  must provide CONFIG_SYS_MALLOC_F_LEN to set the size.
+	  must provide CONFIG_SPL_SYS_MALLOC_F_LEN to set the size.
 	  In most cases driver model will only allocate a few uclasses
 	  and devices in SPL, so 1KB should be enable. See
-	  CONFIG_SYS_MALLOC_F_LEN for more details on how to enable it.
+	  CONFIG_SPL_SYS_MALLOC_F_LEN for more details on how to enable it.
 
 config TPL_DM
 	bool "Enable Driver Model for TPL"
@@ -29,10 +29,10 @@ config TPL_DM
 	  suitable malloc() implementation. If you are not using the
 	  full malloc() enabled by CONFIG_SYS_SPL_MALLOC_START,
 	  consider using CONFIG_SYS_MALLOC_SIMPLE. In that case you
-	  must provide CONFIG_SYS_MALLOC_F_LEN to set the size.
+	  must provide CONFIG_SPL_SYS_MALLOC_F_LEN to set the size.
 	  In most cases driver model will only allocate a few uclasses
 	  and devices in SPL, so 1KB should be enough. See
-	  CONFIG_SYS_MALLOC_F_LEN for more details on how to enable it.
+	  CONFIG_SPL_SYS_MALLOC_F_LEN for more details on how to enable it.
 	  Disable this for very small implementations.
 
 config DM_WARN

+ 2 - 2
drivers/serial/serial-uclass.c

@@ -23,8 +23,8 @@ DECLARE_GLOBAL_DATA_PTR;
  */
 static const unsigned long baudrate_table[] = CONFIG_SYS_BAUDRATE_TABLE;
 
-#ifndef CONFIG_SYS_MALLOC_F_LEN
-#error "Serial is required before relocation - define CONFIG_SYS_MALLOC_F_LEN to make this work"
+#if !CONFIG_VAL(SYS_MALLOC_F_LEN)
+#error "Serial is required before relocation - define CONFIG_$(SPL_)SYS_MALLOC_F_LEN to make this work"
 #endif
 
 static int serial_check_stdout(const void *blob, struct udevice **devp)

+ 1 - 1
include/asm-generic/global_data.h

@@ -88,7 +88,7 @@ typedef struct global_data {
 #endif
 	unsigned int timebase_h;
 	unsigned int timebase_l;
-#ifdef CONFIG_SYS_MALLOC_F_LEN
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
 	unsigned long malloc_base;	/* base address of early malloc() */
 	unsigned long malloc_limit;	/* limit address */
 	unsigned long malloc_ptr;	/* current address */

+ 1 - 1
lib/asm-offsets.c

@@ -28,7 +28,7 @@ int main(void)
 	DEFINE(GD_SIZE, sizeof(struct global_data));
 
 	DEFINE(GD_BD, offsetof(struct global_data, bd));
-#ifdef CONFIG_SYS_MALLOC_F_LEN
+#if CONFIG_VAL(SYS_MALLOC_F_LEN)
 	DEFINE(GD_MALLOC_BASE, offsetof(struct global_data, malloc_base));
 #endif
 

+ 1 - 1
lib/efi/efi_app.c

@@ -48,7 +48,7 @@ static efi_status_t setup_memory(struct efi_priv *priv)
 		return ret;
 	memset(gd, '\0', sizeof(*gd));
 
-	gd->malloc_base = (ulong)efi_malloc(priv, CONFIG_SYS_MALLOC_F_LEN,
+	gd->malloc_base = (ulong)efi_malloc(priv, CONFIG_VAL(SYS_MALLOC_F_LEN),
 					    &ret);
 	if (!gd->malloc_base)
 		return ret;