|
@@ -138,74 +138,6 @@ endmenu # General setup
|
|
|
|
|
|
menu "Boot images"
|
|
|
|
|
|
-config SUPPORT_SPL
|
|
|
- bool
|
|
|
-
|
|
|
-config SUPPORT_TPL
|
|
|
- bool
|
|
|
-
|
|
|
-config SPL
|
|
|
- bool
|
|
|
- depends on SUPPORT_SPL
|
|
|
- prompt "Enable SPL"
|
|
|
- help
|
|
|
- If you want to build SPL as well as the normal image, say Y.
|
|
|
-
|
|
|
-config SPL_SYS_MALLOC_SIMPLE
|
|
|
- bool
|
|
|
- depends on SPL
|
|
|
- prompt "Only use malloc_simple functions in the SPL"
|
|
|
- help
|
|
|
- Say Y here to only use the *_simple malloc functions from
|
|
|
- malloc_simple.c, rather then using the versions from dlmalloc.c;
|
|
|
- this will make the SPL binary smaller at the cost of more heap
|
|
|
- usage as the *_simple malloc functions do not re-use free-ed mem.
|
|
|
-
|
|
|
-config SPL_STACK_R
|
|
|
- depends on SPL
|
|
|
- bool "Enable SDRAM location for SPL stack"
|
|
|
- help
|
|
|
- SPL starts off execution in SRAM and thus typically has only a small
|
|
|
- stack available. Since SPL sets up DRAM while in its board_init_f()
|
|
|
- function, it is possible for the stack to move there before
|
|
|
- board_init_r() is reached. This option enables a special SDRAM
|
|
|
- location for the SPL stack. U-Boot SPL switches to this after
|
|
|
- board_init_f() completes, and before board_init_r() starts.
|
|
|
-
|
|
|
-config SPL_STACK_R_ADDR
|
|
|
- depends on SPL_STACK_R
|
|
|
- hex "SDRAM location for SPL stack"
|
|
|
- help
|
|
|
- Specify the address in SDRAM for the SPL stack. This will be set up
|
|
|
- before board_init_r() is called.
|
|
|
-
|
|
|
-config SPL_STACK_R_MALLOC_SIMPLE_LEN
|
|
|
- depends on SPL_STACK_R && SPL_SYS_MALLOC_SIMPLE
|
|
|
- hex "Size of malloc_simple heap after switching to DRAM SPL stack"
|
|
|
- default 0x100000
|
|
|
- help
|
|
|
- Specify the amount of the stack to use as memory pool for
|
|
|
- malloc_simple after switching the stack to DRAM. This may be set
|
|
|
- to give board_init_r() a larger heap then the initial heap in
|
|
|
- SRAM which is limited to SYS_MALLOC_F_LEN bytes.
|
|
|
-
|
|
|
-config SPL_SEPARATE_BSS
|
|
|
- depends on SPL
|
|
|
- bool "BSS section is in a different memory region from text"
|
|
|
- help
|
|
|
- Some platforms need a large BSS region in SPL and can provide this
|
|
|
- because RAM is already set up. In this case BSS can be moved to RAM.
|
|
|
- This option should then be enabled so that the correct device tree
|
|
|
- location is used. Normally we put the device tree at the end of BSS
|
|
|
- but with this option enabled, it goes at _image_binary_end.
|
|
|
-
|
|
|
-config TPL
|
|
|
- bool
|
|
|
- depends on SPL && SUPPORT_TPL
|
|
|
- prompt "Enable TPL"
|
|
|
- help
|
|
|
- If you want to build TPL as well as the normal image and SPL, say Y.
|
|
|
-
|
|
|
config FIT
|
|
|
bool "Support Flattened Image Tree"
|
|
|
help
|