Browse Source

sunxi: support loading with SPL > 32KB

H616 supports and needs bigger SPL than 32 KiB, mostly due to big DRAM
driver and need for PMIC configuration, which pulls several drivers which
are not needed otherwise.

spl_mmc_get_uboot_raw_sector() will now compare pre-configured size with
that, reported in SPL header. If size in header is bigger, it will use
that value instead.

In the process of function rework, also add missing function argument.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Andre Przywara 3 years ago
parent
commit
c0b417b2f1
2 changed files with 18 additions and 3 deletions
  1. 16 2
      arch/arm/mach-sunxi/board.c
  2. 2 1
      common/spl/Kconfig

+ 16 - 2
arch/arm/mach-sunxi/board.c

@@ -277,15 +277,29 @@ uint32_t sunxi_get_boot_device(void)
 }
 
 #ifdef CONFIG_SPL_BUILD
+static u32 sunxi_get_spl_size(void)
+{
+	if (!is_boot0_magic(SPL_ADDR + 4)) /* eGON.BT0 */
+		return 0;
+
+	return readl(SPL_ADDR + 0x10);
+}
+
 /*
  * The eGON SPL image can be located at 8KB or at 128KB into an SD card or
  * an eMMC device. The boot source has bit 4 set in the latter case.
  * By adding 120KB to the normal offset when booting from a "high" location
  * we can support both cases.
+ * Also U-Boot proper is located at least 32KB after the SPL, but will
+ * immediately follow the SPL if that is bigger than that.
  */
-unsigned long spl_mmc_get_uboot_raw_sector(struct mmc *mmc)
+unsigned long spl_mmc_get_uboot_raw_sector(struct mmc *mmc,
+					   unsigned long raw_sect)
 {
-	unsigned long sector = CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR;
+	unsigned long spl_size = sunxi_get_spl_size();
+	unsigned long sector;
+
+	sector = max(raw_sect, spl_size / 512);
 
 	switch (sunxi_get_boot_source()) {
 	case SUNXI_BOOTED_FROM_MMC0_HIGH:

+ 2 - 1
common/spl/Kconfig

@@ -325,7 +325,7 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
 config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
 	hex "Address on the MMC to load U-Boot from"
 	depends on SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
-	default 0x50 if ARCH_SUNXI
+	default 0x40 if ARCH_SUNXI
 	default 0x75 if ARCH_DAVINCI
 	default 0x8a if ARCH_MX6 || ARCH_MX7
 	default 0x100 if ARCH_UNIPHIER
@@ -342,6 +342,7 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
 config SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET
 	hex "U-Boot main hardware partition image offset"
 	depends on SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
+	default 0x10 if ARCH_SUNXI
 	default 0x0
 	help
 	  On some platforms SPL location depends on hardware partition. The ROM