Browse Source

Patches by Jon Loeliger, 24 Aug 2004:
- Add support for the MPC8541 and MPC8555 CDS boards
- Cleanup eth?addr handling: make dependent on CONFIG_ETH?ADDR

wdenk 19 years ago
parent
commit
03f5c55021

+ 4 - 2
CHANGELOG

@@ -2,11 +2,13 @@
 Changes since U-Boot 1.1.1:
 ======================================================================
 
-* Patch by Jon Loeliger, 24 Aug 2004:
+* Patches by Jon Loeliger, 24 Aug 2004:
+  - Add support for the MPC8541 and MPC8555 CDS boards
+  - Cleanup eth?addr handling: make dependent on CONFIG_ETH?ADDR
+  - Convert MPC85xxADS to use common CFI flash driver
   - Fix PCI window on MPC85xx; remove unneeded PCI initialization
     from board_early_init_f()
   - Provide SW workaround for PCI initialization on 85xx CDS
-  - Convert MPC85xxADS to use common CFI flash driver
 
 * Patches by George G. Davis, 24 Aug 2004:
   - Enable ramdisk/initrd tagged param support for omap1610h2_config

+ 2 - 1
MAKEALL

@@ -100,7 +100,8 @@ LIST_8260="	\
 #########################################################################
 
 LIST_85xx="	\
-	MPC8540ADS	MPC8560ADS	sbc8560		stxgp3		\
+	MPC8540ADS	MPC8541CDS	MPC8555CDS	MPC8560ADS	\
+	sbc8560		stxgp3		\
 "
 
 #########################################################################

+ 8 - 2
Makefile

@@ -1087,8 +1087,11 @@ MPC8540ADS_config:	unconfig
 MPC8560ADS_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc85xx mpc8560ads
 
-stxgp3_config:		unconfig
-	@./mkconfig $(@:_config=) ppc mpc85xx stxgp3
+MPC8541CDS_config:	unconfig
+	@./mkconfig $(@:_config=) ppc mpc85xx mpc8541cds cds
+
+MPC8555CDS_config:	unconfig
+	@./mkconfig $(@:_config=) ppc mpc85xx mpc8555cds cds
 
 sbc8560_config \
 sbc8560_33_config \
@@ -1102,6 +1105,9 @@ sbc8560_66_config:      unconfig
 	fi
 	@./mkconfig -a sbc8560 ppc mpc85xx sbc8560
 
+stxgp3_config:		unconfig
+	@./mkconfig $(@:_config=) ppc mpc85xx stxgp3
+
 #########################################################################
 ## 74xx/7xx Systems
 #########################################################################

+ 95 - 0
board/cds/common/cadmus.c

@@ -0,0 +1,95 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+
+
+/*
+ * CADMUS Board System Registers
+ */
+#ifndef CFG_CADMUS_BASE_REG
+#define CFG_CADMUS_BASE_REG	(CADMUS_BASE_ADDR + 0x4000)
+#endif
+
+typedef struct cadmus_reg {
+    u_char cm_ver;		/* Board version */
+    u_char cm_csr;		/* General control/status */
+    u_char cm_rst;		/* Reset control */
+    u_char cm_hsclk;		/* High speed clock */
+    u_char cm_hsxclk;		/* High speed clock extended */
+    u_char cm_led;		/* LED data */
+    u_char cm_pci;		/* PCI control/status */
+    u_char cm_dma;		/* DMA control */
+    u_char cm_reserved[248];	/* Total 256 bytes */
+} cadmus_reg_t;
+
+
+unsigned int
+get_board_version(void)
+{
+	volatile cadmus_reg_t *cadmus = (cadmus_reg_t *)CFG_CADMUS_BASE_REG;
+
+	return cadmus->cm_ver;
+}
+
+
+unsigned long
+get_clock_freq(void)
+{
+	volatile cadmus_reg_t *cadmus = (cadmus_reg_t *)CFG_CADMUS_BASE_REG;
+
+	uint pci1_speed = (cadmus->cm_pci >> 2) & 0x3; /* PSPEED in [4:5] */
+
+	if (pci1_speed == 0) {
+		return 33000000;
+	} else if (pci1_speed == 1) {
+		return 66000000;
+	} else {
+		/* Really, unknown. Be safe? */
+		return 33000000;
+	}
+}
+
+
+unsigned int
+get_pci_slot(void)
+{
+	volatile cadmus_reg_t *cadmus = (cadmus_reg_t *)CFG_CADMUS_BASE_REG;
+
+	/*
+	 * PCI slot in USER bits CSR[6:7] by convention.
+	 */
+	return ((cadmus->cm_csr >> 6) & 0x3) + 1;
+}
+
+
+unsigned int
+get_pci_dual(void)
+{
+	volatile cadmus_reg_t *cadmus = (cadmus_reg_t *)CFG_CADMUS_BASE_REG;
+
+	/*
+	 * PCI DUAL in CM_PCI[3]
+	 */
+	return cadmus->cm_pci & 0x10;
+}

+ 54 - 0
board/cds/common/cadmus.h

@@ -0,0 +1,54 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CADMUS_H_
+#define __CADMUS_H_
+
+
+/*
+ * CADMUS Board System Register interface.
+ */
+
+/*
+ * Returns board version register.
+ */
+extern unsigned int get_board_version(void);
+
+/*
+ * Returns either 33000000 or 66000000 as the SYS_CLK_FREQ.
+ */
+extern unsigned long get_clock_freq(void);
+
+
+/*
+ * Returns 1 - 4, as found in the USER CSR[6:7] bits.
+ */
+extern unsigned int get_pci_slot(void);
+
+
+/*
+ * Returns PCI DUAL as found in CM_PCI[3].
+ */
+extern unsigned int get_pci_dual(void);
+
+
+#endif	/* __CADMUS_H_ */

+ 60 - 0
board/cds/common/eeprom.c

@@ -0,0 +1,60 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+#include <i2c.h>
+
+#include "eeprom.h"
+
+
+typedef struct {
+	char idee_pcbid[4];		/* "CCID" for CDC v1.X */
+	u8 idee_major;
+	u8 idee_minor;
+	char idee_serial[10];
+	char idee_errata[2];
+	char idee_date[8];		/* yyyymmdd */
+	/* The rest of the EEPROM space is reserved */
+} id_eeprom_t;
+
+
+unsigned int
+get_cpu_board_revision(void)
+{
+	uint major = 0;
+	uint minor = 0;
+
+	id_eeprom_t id_eeprom;
+
+	i2c_read(CFG_I2C_EEPROM_ADDR, 0, 2,
+		 (uchar *) &id_eeprom, sizeof(id_eeprom));
+
+	major = id_eeprom.idee_major;
+	minor = id_eeprom.idee_minor;
+
+	if (major == 0xff && minor == 0xff) {
+		major = minor = 0;
+	}
+
+	return MPC85XX_CPU_BOARD_REV(major,minor);
+}

+ 50 - 0
board/cds/common/eeprom.h

@@ -0,0 +1,50 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __EEPROM_H_
+#define __EEPROM_H_
+
+
+/*
+ * EEPROM Board System Register interface.
+ */
+
+
+/*
+ * CPU Board Revision
+ */
+#define MPC85XX_CPU_BOARD_REV(maj, min)	((((maj)&0xff) << 8) | ((min) & 0xff))
+#define MPC85XX_CPU_BOARD_MAJOR(rev)	(((rev) >> 8) & 0xff)
+#define MPC85XX_CPU_BOARD_MINOR(rev)	((rev) & 0xff)
+
+#define MPC85XX_CPU_BOARD_REV_UNKNOWN	MPC85XX_CPU_BOARD_REV(0,0)
+#define MPC85XX_CPU_BOARD_REV_1_0	MPC85XX_CPU_BOARD_REV(1,0)
+#define MPC85XX_CPU_BOARD_REV_1_1	MPC85XX_CPU_BOARD_REV(1,1)
+
+/*
+ * Returns CPU board revision register as a 16-bit value with
+ * the Major in the high byte, and Minor in the low byte.
+ */
+extern unsigned int get_cpu_board_revision(void);
+
+
+#endif	/* __CADMUS_H_ */

+ 51 - 0
board/cds/mpc8541cds/Makefile

@@ -0,0 +1,51 @@
+#
+# Copyright 2004 Freescale Semiconductor.
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= $(BOARD).o \
+	   ../common/cadmus.o \
+	   ../common/eeprom.o
+
+SOBJS	:= init.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

+ 30 - 0
board/cds/mpc8541cds/config.mk

@@ -0,0 +1,30 @@
+#
+# Copyright 2004 Freescale Semiconductor.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# mpc8541cds board
+#
+TEXT_BASE = 0xfff80000
+
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8541=1

+ 255 - 0
board/cds/mpc8541cds/init.S

@@ -0,0 +1,255 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ * Copyright 2002,2003, Motorola Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/cache.h>
+#include <asm/mmu.h>
+#include <config.h>
+#include <mpc85xx.h>
+
+
+/*
+ * TLB0 and TLB1 Entries
+ *
+ * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR.
+ * However, CCSRBAR is then relocated to CFG_CCSRBAR right after
+ * these TLB entries are established.
+ *
+ * The TLB entries for DDR are dynamically setup in spd_sdram()
+ * and use TLB1 Entries 8 through 15 as needed according to the
+ * size of DDR memory.
+ *
+ * MAS0: tlbsel, esel, nv
+ * MAS1: valid, iprot, tid, ts, tsize
+ * MAS2: epn, sharen, x0, x1, w, i, m, g, e
+ * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr
+ */
+
+#define	entry_start \
+	mflr	r1 	;	\
+	bl	0f 	;
+
+#define	entry_end \
+0:	mflr	r0	;	\
+	mtlr	r1	;	\
+	blr		;
+
+
+	.section	.bootpg, "ax"
+	.globl	tlb1_entry
+tlb1_entry:
+	entry_start
+
+	/*
+	 * Number of TLB0 and TLB1 entries in the following table
+	 */
+	.long 13
+
+#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
+	/*
+	 * TLB0		4K	Non-cacheable, guarded
+	 * 0xff700000	4K	Initial CCSRBAR mapping
+	 *
+	 * This ends up at a TLB0 Index==0 entry, and must not collide
+	 * with other TLB0 Entries.
+	 */
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)
+#else
+#error("Update the number of table entries in tlb1_entry")
+#endif
+
+	/*
+	 * TLB0		16K	Cacheable, non-guarded
+	 * 0xd001_0000	16K	Temporary Global data for initialization
+	 *
+	 * Use four 4K TLB0 entries.  These entries must be cacheable
+	 * as they provide the bootstrap memory before the memory
+	 * controler and real memory have been configured.
+	 *
+	 * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
+	 * and must not collide with other TLB0 entries.
+	 */
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+
+	/*
+	 * TLB 0:	16M	Non-cacheable, guarded
+	 * 0xff000000	16M	FLASH
+	 * Out of reset this entry is only 4K.
+	 */
+	.long TLB1_MAS0(1, 0, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 1:	256M	Non-cacheable, guarded
+	 * 0x80000000	256M	PCI1 MEM First half
+	 */
+	.long TLB1_MAS0(1, 1, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 2:	256M	Non-cacheable, guarded
+	 * 0x90000000	256M	PCI1 MEM Second half
+	 */
+	.long TLB1_MAS0(1, 2, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000),
+			0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000),
+			0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 3:	256M	Non-cacheable, guarded
+	 * 0xa0000000	256M	PCI2 MEM First half
+	 */
+	.long TLB1_MAS0(1, 3, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 4:	256M	Non-cacheable, guarded
+	 * 0xb0000000	256M	PCI2 MEM Second half
+	 */
+	.long TLB1_MAS0(1, 4, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE + 0x10000000),
+			0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE + 0x10000000),
+			0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 5:	64M	Non-cacheable, guarded
+	 * 0xe000_0000	1M	CCSRBAR
+	 * 0xe200_0000	16M	PCI1 IO
+	 * 0xe300_0000	16M	PCI2 IO
+	 */
+	.long TLB1_MAS0(1, 5, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 6:	64M	Cacheable, non-guarded
+	 * 0xf000_0000	64M	LBC SDRAM
+	 */
+	.long TLB1_MAS0(1, 6, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 7:	1M	Non-cacheable, guarded
+	 * 0xf8000000	1M	CADMUS registers
+	 */
+	.long TLB1_MAS0(1, 7, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M)
+	.long TLB1_MAS2(E500_TLB_EPN(CADMUS_BASE_ADDR), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CADMUS_BASE_ADDR), 0,0,0,0,0,1,0,1,0,1)
+
+	entry_end
+
+/*
+ * LAW(Local Access Window) configuration:
+ *
+ * 0x0000_0000     0x7fff_ffff     DDR                     2G
+ * 0x8000_0000     0x9fff_ffff     PCI1 MEM                512M
+ * 0xa000_0000     0xbfff_ffff     PCI2 MEM                512M
+ * 0xe000_0000     0xe000_ffff     CCSR                    1M
+ * 0xe200_0000     0xe2ff_ffff     PCI1 IO                 16M
+ * 0xe300_0000     0xe3ff_ffff     PCI2 IO                 16M
+ * 0xf000_0000     0xf7ff_ffff     SDRAM                   128M
+ * 0xf800_0000     0xf80f_ffff     NVRAM/CADMUS (*)        1M
+ * 0xff00_0000     0xff7f_ffff     FLASH (2nd bank)        8M
+ * 0xff80_0000     0xffff_ffff     FLASH (boot bank)       8M
+ *
+ * Notes:
+ *    CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ *    If flash is 8M at default position (last 8M), no LAW needed.
+ *
+ * The defines below are 1-off of the actual LAWAR0 usage.
+ * So LAWAR3 define uses the LAWAR4 register in the ECM.
+ */
+
+#define LAWBAR0 0
+#define LAWAR0  ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
+
+#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
+#define LAWAR1 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+#define LAWBAR2 ((CFG_PCI2_MEM_BASE>>12) & 0xfffff)
+#define LAWAR2 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
+#define LAWAR3 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+#define LAWBAR4 ((CFG_PCI2_IO_BASE>>12) & 0xfffff)
+#define LAWAR4 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+/* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
+#define LAWBAR5 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
+#define LAWAR5 	(LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+	.section .bootpg, "ax"
+	.globl	law_entry
+
+law_entry:
+	entry_start
+	.long 6
+	.long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
+	.long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5
+	entry_end

+ 373 - 0
board/cds/mpc8541cds/mpc8541cds.c

@@ -0,0 +1,373 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <spd.h>
+
+#include "../common/cadmus.h"
+#include "../common/eeprom.h"
+
+#if defined(CONFIG_DDR_ECC)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+extern long int spd_sdram(void);
+
+void local_bus_init(void);
+void sdram_init(void);
+
+
+
+int
+board_early_init_f(void)
+{
+    return 0;
+}
+
+
+int
+checkboard(void)
+{
+    volatile immap_t *immap = (immap_t *)CFG_CCSRBAR;
+    volatile ccsr_gur_t *gur = &immap->im_gur;
+
+    /* PCI slot in USER bits CSR[6:7] by convention. */
+    uint pci_slot = get_pci_slot();
+
+    uint pci_dual = get_pci_dual();		/* PCI DUAL in CM_PCI[3] */
+    uint pci1_32 = gur->pordevsr & 0x10000;	/* PORDEVSR[15] */
+    uint pci1_clk_sel = gur->porpllsr & 0x8000; /* PORPLLSR[16] */
+    uint pci2_clk_sel = gur->porpllsr & 0x4000; /* PORPLLSR[17] */
+
+    uint pci1_speed = get_clock_freq();		/* PCI PSPEED in [4:5] */
+
+    uint cpu_board_rev = get_cpu_board_revision();
+
+    printf("Board: CDS Version 0x%02x, PCI Slot %d\n",
+	   get_board_version(),
+	   pci_slot);
+
+    printf("CPU Board Revision %d.%d (0x%04x)\n",
+	   MPC85XX_CPU_BOARD_MAJOR(cpu_board_rev),
+	   MPC85XX_CPU_BOARD_MINOR(cpu_board_rev),
+	   cpu_board_rev);
+
+    printf("    PCI1: %d bit, %s MHz, %s\n",
+	   (pci1_32) ? 32 : 64,
+	   (pci1_speed == 33000000) ? "33" :
+	   (pci1_speed == 66000000) ? "66" : "unknown",
+	   pci1_clk_sel ? "sync" : "async"
+	   );
+
+    if (pci_dual) {
+	printf("    PCI2: 32 bit, 66 MHz, %s\n",
+	       pci2_clk_sel ? "sync" : "async"
+	       );
+    } else {
+	printf("    PCI2: disabled\n");
+    }
+
+    /*
+     * Initialize local bus.
+     */
+    local_bus_init();
+
+    return 0;
+}
+
+
+long int
+initdram(int board_type)
+{
+	long dram_size = 0;
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+
+	puts("Initializing\n");
+
+#if defined(CONFIG_DDR_DLL)
+	{
+		/*
+		 * Work around to stabilize DDR DLL MSYNC_IN.
+		 * Errata DDR9 seems to have been fixed.
+		 * This is now the workaround for Errata DDR11:
+		 *    Override DLL = 1, Course Adj = 1, Tap Select = 0
+		 */
+
+		volatile ccsr_gur_t *gur= &immap->im_gur;
+
+		gur->ddrdllcr = 0x81000000;
+		asm("sync;isync;msync");
+		udelay(200);
+	}
+#endif
+
+	dram_size = spd_sdram();
+
+
+#if defined(CONFIG_DDR_ECC)
+	/*
+	 * Initialize and enable DDR ECC.
+	 */
+	ddr_enable_ecc(dram_size);
+#endif
+
+
+	/*
+	 * SDRAM Initialization
+	 */
+	sdram_init();
+
+	puts("    DDR: ");
+	return dram_size;
+}
+
+
+/*
+ * Initialize Local Bus
+ */
+
+void
+local_bus_init(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	volatile ccsr_gur_t *gur = &immap->im_gur;
+	volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+
+	uint clkdiv;
+	uint lbc_hz;
+	sys_info_t sysinfo;
+	uint temp_lbcdll;
+
+	/*
+	 * Errata LBC11.
+	 * Fix Local Bus clock glitch when DLL is enabled.
+	 *
+	 * If localbus freq is < 66Mhz, DLL bypass mode must be used.
+	 * If localbus freq is > 133Mhz, DLL can be safely enabled.
+	 * Between 66 and 133, the DLL is enabled with an override workaround.
+	 */
+
+	get_sys_info(&sysinfo);
+	clkdiv = lbc->lcrr & 0x0f;
+	lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
+
+	if (lbc_hz < 66) {
+		lbc->lcrr |= 0x80000000;	/* DLL Bypass */
+
+	} else if (lbc_hz >= 133) {
+		lbc->lcrr &= (~0x80000000);		/* DLL Enabled */
+
+	} else {
+		lbc->lcrr &= (~0x8000000);	/* DLL Enabled */
+		udelay(200);
+
+		/*
+		 * Sample LBC DLL ctrl reg, upshift it to set the
+		 * override bits.
+		 */
+		temp_lbcdll = gur->lbcdllcr;
+		gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
+		asm("sync;isync;msync");
+	}
+}
+
+
+/*
+ * Initialize SDRAM memory on the Local Bus.
+ */
+
+void
+sdram_init(void)
+{
+#if defined(CFG_OR2_PRELIM) && defined(CFG_BR2_PRELIM)
+
+	uint idx;
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+	uint *sdram_addr = (uint *)CFG_LBC_SDRAM_BASE;
+	uint cpu_board_rev;
+	uint lsdmr_common;
+
+	puts("    SDRAM: ");
+
+	print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
+
+	/*
+	 * Setup SDRAM Base and Option Registers
+	 */
+	lbc->or2 = CFG_OR2_PRELIM;
+	asm("msync");
+
+	lbc->br2 = CFG_BR2_PRELIM;
+	asm("msync");
+
+	lbc->lbcr = CFG_LBC_LBCR;
+	asm("msync");
+
+
+	lbc->lsrt = CFG_LBC_LSRT;
+	lbc->mrtpr = CFG_LBC_MRTPR;
+	asm("msync");
+
+	/*
+	 * Determine which address lines to use baed on CPU board rev.
+	 */
+	cpu_board_rev = get_cpu_board_revision();
+	lsdmr_common = CFG_LBC_LSDMR_COMMON;
+	if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_0) {
+		lsdmr_common |= CFG_LBC_LSDMR_BSMA1617;
+	} else if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_1) {
+		lsdmr_common |= CFG_LBC_LSDMR_BSMA1516;
+	} else {
+		/*
+		 * Assume something unable to identify itself is
+		 * really old, and likely has lines 16/17 mapped.
+		 */
+		lsdmr_common |= CFG_LBC_LSDMR_BSMA1617;
+	}
+
+	/*
+	 * Issue PRECHARGE ALL command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_PCHALL;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(100);
+
+	/*
+	 * Issue 8 AUTO REFRESH commands.
+	 */
+	for (idx = 0; idx < 8; idx++) {
+		lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_ARFRSH;
+		asm("sync;msync");
+		*sdram_addr = 0xff;
+		ppcDcbf((unsigned long) sdram_addr);
+		udelay(100);
+	}
+
+	/*
+	 * Issue 8 MODE-set command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_MRW;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(100);
+
+	/*
+	 * Issue NORMAL OP command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_NORMAL;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(200);    /* Overkill. Must wait > 200 bus cycles */
+
+#endif	/* enable SDRAM init */
+}
+
+
+#if defined(CFG_DRAM_TEST)
+int
+testdram(void)
+{
+	uint *pstart = (uint *) CFG_MEMTEST_START;
+	uint *pend = (uint *) CFG_MEMTEST_END;
+	uint *p;
+
+	printf("Testing DRAM from 0x%08x to 0x%08x\n",
+	       CFG_MEMTEST_START,
+	       CFG_MEMTEST_END);
+
+	printf("DRAM test phase 1:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0xaaaaaaaa;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0xaaaaaaaa) {
+			printf ("DRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("DRAM test phase 2:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0x55555555;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0x55555555) {
+			printf ("DRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("DRAM test passed.\n");
+	return 0;
+}
+#endif
+
+
+
+#if defined(CONFIG_PCI)
+
+/*
+ * Initialize PCI Devices, report devices found.
+ */
+
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_mpc85xxcds_config_table[] = {
+    { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
+      PCI_IDSEL_NUMBER, PCI_ANY_ID,
+      pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
+				   PCI_ENET0_MEMADDR,
+				   PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
+      } },
+    { }
+};
+#endif
+
+
+static struct pci_controller hose = {
+#ifndef CONFIG_PCI_PNP
+	config_table: pci_mpc85xxcds_config_table,
+#endif
+};
+
+#endif	/* CONFIG_PCI */
+
+
+void
+pci_init_board(void)
+{
+#ifdef CONFIG_PCI
+	extern void pci_mpc85xx_init(struct pci_controller *hose);
+
+	pci_mpc85xx_init(&hose);
+#endif
+}

+ 147 - 0
board/cds/mpc8541cds/u-boot.lds

@@ -0,0 +1,147 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/mpc85xx/start.o	(.bootpg)
+    board/cds/mpc8541cds/init.o (.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc85xx/start.o	(.text)
+    board/cds/mpc8541cds/init.o (.text)
+    cpu/mpc85xx/traps.o (.text)
+    cpu/mpc85xx/interrupts.o (.text)
+    cpu/mpc85xx/cpu_init.o (.text)
+    cpu/mpc85xx/cpu.o (.text)
+    cpu/mpc85xx/tsec.o (.text)
+    cpu/mpc85xx/speed.o (.text)
+    cpu/mpc85xx/pci.o (.text)
+    common/dlmalloc.o (.text)
+    lib_generic/crc32.o (.text)
+    lib_ppc/extable.o (.text)
+    lib_generic/zlib.o (.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+   }
+    _etext = .;
+    PROVIDE (etext = .);
+    .rodata    :
+   {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

+ 51 - 0
board/cds/mpc8555cds/Makefile

@@ -0,0 +1,51 @@
+#
+# Copyright 2004 Freescale Semiconductor.
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= $(BOARD).o \
+	   ../common/cadmus.o \
+	   ../common/eeprom.o
+
+SOBJS	:= init.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

+ 30 - 0
board/cds/mpc8555cds/config.mk

@@ -0,0 +1,30 @@
+#
+# Copyright 2004 Freescale Semiconductor.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# mpc8555cds board
+#
+TEXT_BASE = 0xfff80000
+
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8555=1

+ 255 - 0
board/cds/mpc8555cds/init.S

@@ -0,0 +1,255 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ * Copyright 2002,2003, Motorola Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/cache.h>
+#include <asm/mmu.h>
+#include <config.h>
+#include <mpc85xx.h>
+
+
+/*
+ * TLB0 and TLB1 Entries
+ *
+ * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR.
+ * However, CCSRBAR is then relocated to CFG_CCSRBAR right after
+ * these TLB entries are established.
+ *
+ * The TLB entries for DDR are dynamically setup in spd_sdram()
+ * and use TLB1 Entries 8 through 15 as needed according to the
+ * size of DDR memory.
+ *
+ * MAS0: tlbsel, esel, nv
+ * MAS1: valid, iprot, tid, ts, tsize
+ * MAS2: epn, sharen, x0, x1, w, i, m, g, e
+ * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr
+ */
+
+#define	entry_start \
+	mflr	r1 	;	\
+	bl	0f 	;
+
+#define	entry_end \
+0:	mflr	r0	;	\
+	mtlr	r1	;	\
+	blr		;
+
+
+	.section	.bootpg, "ax"
+	.globl	tlb1_entry
+tlb1_entry:
+	entry_start
+
+	/*
+	 * Number of TLB0 and TLB1 entries in the following table
+	 */
+	.long 13
+
+#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
+	/*
+	 * TLB0		4K	Non-cacheable, guarded
+	 * 0xff700000	4K	Initial CCSRBAR mapping
+	 *
+	 * This ends up at a TLB0 Index==0 entry, and must not collide
+	 * with other TLB0 Entries.
+	 */
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)
+#else
+#error("Update the number of table entries in tlb1_entry")
+#endif
+
+	/*
+	 * TLB0		16K	Cacheable, non-guarded
+	 * 0xd001_0000	16K	Temporary Global data for initialization
+	 *
+	 * Use four 4K TLB0 entries.  These entries must be cacheable
+	 * as they provide the bootstrap memory before the memory
+	 * controler and real memory have been configured.
+	 *
+	 * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
+	 * and must not collide with other TLB0 entries.
+	 */
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+
+	/*
+	 * TLB 0:	16M	Non-cacheable, guarded
+	 * 0xff000000	16M	FLASH
+	 * Out of reset this entry is only 4K.
+	 */
+	.long TLB1_MAS0(1, 0, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 1:	256M	Non-cacheable, guarded
+	 * 0x80000000	256M	PCI1 MEM First half
+	 */
+	.long TLB1_MAS0(1, 1, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 2:	256M	Non-cacheable, guarded
+	 * 0x90000000	256M	PCI1 MEM Second half
+	 */
+	.long TLB1_MAS0(1, 2, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000),
+			0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000),
+			0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 3:	256M	Non-cacheable, guarded
+	 * 0xa0000000	256M	PCI2 MEM First half
+	 */
+	.long TLB1_MAS0(1, 3, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 4:	256M	Non-cacheable, guarded
+	 * 0xb0000000	256M	PCI2 MEM Second half
+	 */
+	.long TLB1_MAS0(1, 4, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE + 0x10000000),
+			0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE + 0x10000000),
+			0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 5:	64M	Non-cacheable, guarded
+	 * 0xe000_0000	1M	CCSRBAR
+	 * 0xe200_0000	16M	PCI1 IO
+	 * 0xe300_0000	16M	PCI2 IO
+	 */
+	.long TLB1_MAS0(1, 5, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 6:	64M	Cacheable, non-guarded
+	 * 0xf000_0000	64M	LBC SDRAM
+	 */
+	.long TLB1_MAS0(1, 6, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 7:	1M	Non-cacheable, guarded
+	 * 0xf8000000	1M	CADMUS registers
+	 */
+	.long TLB1_MAS0(1, 7, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M)
+	.long TLB1_MAS2(E500_TLB_EPN(CADMUS_BASE_ADDR), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CADMUS_BASE_ADDR), 0,0,0,0,0,1,0,1,0,1)
+
+	entry_end
+
+/*
+ * LAW(Local Access Window) configuration:
+ *
+ * 0x0000_0000     0x7fff_ffff     DDR                     2G
+ * 0x8000_0000     0x9fff_ffff     PCI1 MEM                512M
+ * 0xa000_0000     0xbfff_ffff     PCI2 MEM                512M
+ * 0xe000_0000     0xe000_ffff     CCSR                    1M
+ * 0xe200_0000     0xe2ff_ffff     PCI1 IO                 16M
+ * 0xe300_0000     0xe3ff_ffff     PCI2 IO                 16M
+ * 0xf000_0000     0xf7ff_ffff     SDRAM                   128M
+ * 0xf800_0000     0xf80f_ffff     NVRAM/CADMUS (*)        1M
+ * 0xff00_0000     0xff7f_ffff     FLASH (2nd bank)        8M
+ * 0xff80_0000     0xffff_ffff     FLASH (boot bank)       8M
+ *
+ * Notes:
+ *    CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ *    If flash is 8M at default position (last 8M), no LAW needed.
+ *
+ * The defines below are 1-off of the actual LAWAR0 usage.
+ * So LAWAR3 define uses the LAWAR4 register in the ECM.
+ */
+
+#define LAWBAR0 0
+#define LAWAR0  ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
+
+#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
+#define LAWAR1 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+#define LAWBAR2 ((CFG_PCI2_MEM_BASE>>12) & 0xfffff)
+#define LAWAR2 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
+#define LAWAR3 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+#define LAWBAR4 ((CFG_PCI2_IO_BASE>>12) & 0xfffff)
+#define LAWAR4 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+/* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
+#define LAWBAR5 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
+#define LAWAR5 	(LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+	.section .bootpg, "ax"
+	.globl	law_entry
+
+law_entry:
+	entry_start
+	.long 6
+	.long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
+	.long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5
+	entry_end

+ 371 - 0
board/cds/mpc8555cds/mpc8555cds.c

@@ -0,0 +1,371 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <spd.h>
+
+#include "../common/cadmus.h"
+#include "../common/eeprom.h"
+
+#if defined(CONFIG_DDR_ECC)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+extern long int spd_sdram(void);
+
+void local_bus_init(void);
+void sdram_init(void);
+
+
+
+int
+board_early_init_f(void)
+{
+    return 0;
+}
+
+
+int
+checkboard(void)
+{
+    volatile immap_t *immap = (immap_t *)CFG_CCSRBAR;
+    volatile ccsr_gur_t *gur = &immap->im_gur;
+
+    /* PCI slot in USER bits CSR[6:7] by convention. */
+    uint pci_slot = get_pci_slot();
+
+    uint pci_dual = get_pci_dual();		/* PCI DUAL in CM_PCI[3] */
+    uint pci1_32 = gur->pordevsr & 0x10000;	/* PORDEVSR[15] */
+    uint pci1_clk_sel = gur->porpllsr & 0x8000; /* PORPLLSR[16] */
+    uint pci2_clk_sel = gur->porpllsr & 0x4000; /* PORPLLSR[17] */
+
+    uint pci1_speed = get_clock_freq();		/* PCI PSPEED in [4:5] */
+
+    uint cpu_board_rev = get_cpu_board_revision();
+
+    printf("Board: CDS Version 0x%02x, PCI Slot %d\n",
+	   get_board_version(),
+	   pci_slot);
+
+    printf("CPU Board Revision %d.%d (0x%04x)\n",
+	   MPC85XX_CPU_BOARD_MAJOR(cpu_board_rev),
+	   MPC85XX_CPU_BOARD_MINOR(cpu_board_rev),
+	   cpu_board_rev);
+
+    printf("    PCI1: %d bit, %s MHz, %s\n",
+	   (pci1_32) ? 32 : 64,
+	   (pci1_speed == 33000000) ? "33" :
+	   (pci1_speed == 66000000) ? "66" : "unknown",
+	   pci1_clk_sel ? "sync" : "async"
+	   );
+
+    if (pci_dual) {
+	printf("    PCI2: 32 bit, 66 MHz, %s\n",
+	       pci2_clk_sel ? "sync" : "async"
+	       );
+    } else {
+	printf("    PCI2: disabled\n");
+    }
+
+    /*
+     * Initialize local bus.
+     */
+    local_bus_init();
+
+    return 0;
+}
+
+
+long int
+initdram(int board_type)
+{
+	long dram_size = 0;
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+
+	puts("Initializing\n");
+
+#if defined(CONFIG_DDR_DLL)
+	{
+		/*
+		 * Work around to stabilize DDR DLL MSYNC_IN.
+		 * Errata DDR9 seems to have been fixed.
+		 * This is now the workaround for Errata DDR11:
+		 *    Override DLL = 1, Course Adj = 1, Tap Select = 0
+		 */
+
+		volatile ccsr_gur_t *gur= &immap->im_gur;
+
+		gur->ddrdllcr = 0x81000000;
+		asm("sync;isync;msync");
+		udelay(200);
+	}
+#endif
+
+	dram_size = spd_sdram();
+
+
+#if defined(CONFIG_DDR_ECC)
+	/*
+	 * Initialize and enable DDR ECC.
+	 */
+	ddr_enable_ecc(dram_size);
+#endif
+
+
+	/*
+	 * SDRAM Initialization
+	 */
+	sdram_init();
+
+	puts("    DDR: ");
+	return dram_size;
+}
+
+
+/*
+ * Initialize Local Bus
+ */
+
+void
+local_bus_init(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	volatile ccsr_gur_t *gur = &immap->im_gur;
+	volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+
+	uint clkdiv;
+	uint lbc_hz;
+	sys_info_t sysinfo;
+	uint temp_lbcdll;
+
+	/*
+	 * Errata LBC11.
+	 * Fix Local Bus clock glitch when DLL is enabled.
+	 *
+	 * If localbus freq is < 66Mhz, DLL bypass mode must be used.
+	 * If localbus freq is > 133Mhz, DLL can be safely enabled.
+	 * Between 66 and 133, the DLL is enabled with an override workaround.
+	 */
+
+	get_sys_info(&sysinfo);
+	clkdiv = lbc->lcrr & 0x0f;
+	lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
+
+	if (lbc_hz < 66) {
+		lbc->lcrr |= 0x80000000;	/* DLL Bypass */
+
+	} else if (lbc_hz >= 133) {
+		lbc->lcrr &= (~0x80000000);		/* DLL Enabled */
+
+	} else {
+		lbc->lcrr &= (~0x8000000);	/* DLL Enabled */
+		udelay(200);
+
+		/*
+		 * Sample LBC DLL ctrl reg, upshift it to set the
+		 * override bits.
+		 */
+		temp_lbcdll = gur->lbcdllcr;
+		gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
+		asm("sync;isync;msync");
+	}
+}
+
+
+/*
+ * Initialize SDRAM memory on the Local Bus.
+ */
+
+void
+sdram_init(void)
+{
+#if defined(CFG_OR2_PRELIM) && defined(CFG_BR2_PRELIM)
+
+	uint idx;
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+	uint *sdram_addr = (uint *)CFG_LBC_SDRAM_BASE;
+	uint cpu_board_rev;
+	uint lsdmr_common;
+
+	puts("    SDRAM: ");
+
+	print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
+
+	/*
+	 * Setup SDRAM Base and Option Registers
+	 */
+	lbc->or2 = CFG_OR2_PRELIM;
+	asm("msync");
+
+	lbc->br2 = CFG_BR2_PRELIM;
+	asm("msync");
+
+	lbc->lbcr = CFG_LBC_LBCR;
+	asm("msync");
+
+
+	lbc->lsrt = CFG_LBC_LSRT;
+	lbc->mrtpr = CFG_LBC_MRTPR;
+	asm("msync");
+
+	/*
+	 * Determine which address lines to use baed on CPU board rev.
+	 */
+	cpu_board_rev = get_cpu_board_revision();
+	lsdmr_common = CFG_LBC_LSDMR_COMMON;
+	if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_0) {
+		lsdmr_common |= CFG_LBC_LSDMR_BSMA1617;
+	} else if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_1) {
+		lsdmr_common |= CFG_LBC_LSDMR_BSMA1516;
+	} else {
+		/*
+		 * Assume something unable to identify itself is
+		 * really old, and likely has lines 16/17 mapped.
+		 */
+		lsdmr_common |= CFG_LBC_LSDMR_BSMA1617;
+	}
+
+	/*
+	 * Issue PRECHARGE ALL command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_PCHALL;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(100);
+
+	/*
+	 * Issue 8 AUTO REFRESH commands.
+	 */
+	for (idx = 0; idx < 8; idx++) {
+		lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_ARFRSH;
+		asm("sync;msync");
+		*sdram_addr = 0xff;
+		ppcDcbf((unsigned long) sdram_addr);
+		udelay(100);
+	}
+
+	/*
+	 * Issue 8 MODE-set command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_MRW;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(100);
+
+	/*
+	 * Issue NORMAL OP command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_NORMAL;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(200);    /* Overkill. Must wait > 200 bus cycles */
+
+#endif	/* enable SDRAM init */
+}
+
+
+#if defined(CFG_DRAM_TEST)
+int
+testdram(void)
+{
+	uint *pstart = (uint *) CFG_MEMTEST_START;
+	uint *pend = (uint *) CFG_MEMTEST_END;
+	uint *p;
+
+	printf("Testing DRAM from 0x%08x to 0x%08x\n",
+	       CFG_MEMTEST_START,
+	       CFG_MEMTEST_END);
+
+	printf("DRAM test phase 1:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0xaaaaaaaa;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0xaaaaaaaa) {
+			printf ("DRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("DRAM test phase 2:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0x55555555;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0x55555555) {
+			printf ("DRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("DRAM test passed.\n");
+	return 0;
+}
+#endif
+
+
+
+#if defined(CONFIG_PCI)
+
+/*
+ * Initialize PCI Devices, report devices found.
+ */
+
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_mpc85xxcds_config_table[] = {
+    { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
+      PCI_IDSEL_NUMBER, PCI_ANY_ID,
+      pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
+				   PCI_ENET0_MEMADDR,
+				   PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
+      } },
+    { }
+};
+#endif
+
+
+static struct pci_controller hose = {
+#ifndef CONFIG_PCI_PNP
+	config_table: pci_mpc85xxcds_config_table,
+#endif
+};
+
+#endif	/* CONFIG_PCI */
+
+
+void
+pci_init_board(void)
+{
+#ifdef CONFIG_PCI
+	extern void pci_mpc85xx_init(struct pci_controller *hose);
+
+	pci_mpc85xx_init(&hose);
+#endif
+}

+ 147 - 0
board/cds/mpc8555cds/u-boot.lds

@@ -0,0 +1,147 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/mpc85xx/start.o	(.bootpg)
+    board/cds/mpc8555cds/init.o (.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc85xx/start.o	(.text)
+    board/cds/mpc8555cds/init.o (.text)
+    cpu/mpc85xx/traps.o (.text)
+    cpu/mpc85xx/interrupts.o (.text)
+    cpu/mpc85xx/cpu_init.o (.text)
+    cpu/mpc85xx/cpu.o (.text)
+    cpu/mpc85xx/tsec.o (.text)
+    cpu/mpc85xx/speed.o (.text)
+    cpu/mpc85xx/pci.o (.text)
+    common/dlmalloc.o (.text)
+    lib_generic/crc32.o (.text)
+    lib_ppc/extable.o (.text)
+    lib_generic/zlib.o (.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+   }
+    _etext = .;
+    PROVIDE (etext = .);
+    .rodata    :
+   {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

+ 0 - 537
board/mpc8540ads/flash.c

@@ -1,537 +0,0 @@
-/*
- * (C) Copyright 2003 Motorola Inc.
- *  Xianghua Xiao,(X.Xiao@motorola.com)
- *
- * (C) Copyright 2000, 2001
- *  Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2001, Stuart Hughes, Lineo Inc, stuarth@lineo.com
- * Add support the Sharp chips on the mpc8260ads.
- * I started with board/ip860/flash.c and made changes I found in
- * the MTD project by David Schleef.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-#if !defined(CFG_NO_FLASH)
-
-flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
-
-#if defined(CFG_ENV_IS_IN_FLASH)
-# ifndef  CFG_ENV_ADDR
-#  define CFG_ENV_ADDR	(CFG_FLASH_BASE + CFG_ENV_OFFSET)
-# endif
-# ifndef  CFG_ENV_SIZE
-#  define CFG_ENV_SIZE	CFG_ENV_SECT_SIZE
-# endif
-# ifndef  CFG_ENV_SECT_SIZE
-#  define CFG_ENV_SECT_SIZE  CFG_ENV_SIZE
-# endif
-#endif
-
-#undef DEBUG
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_long *addr, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-static int clear_block_lock_bit(vu_long * addr);
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-	unsigned long size;
-	int i;
-
-	/* Init: enable write,
-	 * or we cannot even write flash commands
-	 */
-	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
-		flash_info[i].flash_id = FLASH_UNKNOWN;
-
-		/* set the default sector offset */
-	}
-
-	/* Static FLASH Bank configuration here - FIXME XXX */
-
-	size = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]);
-
-	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
-		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
-			size, size<<20);
-	}
-
-	/* Re-do sizing to get full correct info */
-	size = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]);
-
-	flash_info[0].size = size;
-
-#if CFG_MONITOR_BASE >= CFG_FLASH_BASE
-	/* monitor protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+monitor_flash_len-1,
-		      &flash_info[0]);
-
-#ifdef	CFG_ENV_IS_IN_FLASH
-	/* ENV protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CFG_ENV_ADDR,
-		      CFG_ENV_ADDR+CFG_ENV_SECT_SIZE-1,
-		      &flash_info[0]);
-#endif
-#endif
-	return (size);
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info  (flash_info_t *info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_INTEL:	printf ("Intel ");		break;
-	case FLASH_MAN_SHARP:   printf ("Sharp ");		break;
-	default:		printf ("Unknown Vendor ");	break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_28F016SV:	printf ("28F016SV (16 Mbit, 32 x 64k)\n");
-				break;
-	case FLASH_28F160S3:	printf ("28F160S3 (16 Mbit, 32 x 512K)\n");
-				break;
-	case FLASH_28F320S3:	printf ("28F320S3 (32 Mbit, 64 x 512K)\n");
-				break;
-	case FLASH_LH28F016SCT: printf ("28F016SC (16 Mbit, 32 x 64K)\n");
-				break;
-	case FLASH_28F640J3A:   printf ("28F640J3A (64 Mbit, 64 x 128K)\n");
-				break;
-	default:		printf ("Unknown Chip Type\n");
-				break;
-	}
-
-	printf ("  Size: %ld MB in %d Sectors\n",
-		info->size >> 20, info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-	for (i=0; i<info->sector_count; ++i) {
-		if ((i % 5) == 0)
-			printf ("\n   ");
-		printf (" %08lX%s",
-			info->start[i],
-			info->protect[i] ? " (RO)" : "     "
-		);
-	}
-	printf ("\n");
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info)
-{
-	short i;
-	ulong value;
-	ulong base = (ulong)addr;
-	ulong sector_offset;
-
-#ifdef DEBUG
-	printf("Check flash at 0x%08x\n",(uint)addr);
-#endif
-	/* Write "Intelligent Identifier" command: read Manufacturer ID */
-	*addr = 0x90909090;
-	udelay(20);
-	asm("sync");
-
-	value = addr[0] & 0x00FF00FF;
-
-#ifdef DEBUG
-	printf("manufacturer=0x%x\n",(uint)value);
-#endif
-	switch (value) {
-	case MT_MANUFACT:	/* SHARP, MT or => Intel */
-	case INTEL_ALT_MANU:
-		info->flash_id = FLASH_MAN_INTEL;
-		break;
-	default:
-		printf("unknown manufacturer: %x\n", (unsigned int)value);
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		return (0);			/* no or unknown flash	*/
-	}
-
-	value = addr[1] & 0x00FF00FF;             /* device ID            */
-
-#ifdef DEBUG
-	printf("deviceID=0x%x\n",(uint)value);
-#endif
-	switch (value) {
-	case (INTEL_ID_28F016S):
-		info->flash_id += FLASH_28F016SV;
-		info->sector_count = 32;
-		info->size = 0x00400000;
-		sector_offset = 0x20000;
-		break;				/* => 2x2 MB		*/
-
-	case (INTEL_ID_28F160S3):
-		info->flash_id += FLASH_28F160S3;
-		info->sector_count = 32;
-		info->size = 0x00400000;
-		sector_offset = 0x20000;
-		break;				/* => 2x2 MB		*/
-
-	case (INTEL_ID_28F320S3):
-		info->flash_id += FLASH_28F320S3;
-		info->sector_count = 64;
-		info->size = 0x00800000;
-		sector_offset = 0x20000;
-		break;				/* => 2x4 MB		*/
-
-	case (INTEL_ID_28F640J3A):
-		info->flash_id += FLASH_28F640J3A;
-		info->sector_count = 64;
-		info->size = 0x01000000;
-		sector_offset = 0x40000;
-		break;                          /* => 2x8 MB             */
-
-	case SHARP_ID_28F016SCL:
-	case SHARP_ID_28F016SCZ:
-		info->flash_id      = FLASH_MAN_SHARP | FLASH_LH28F016SCT;
-		info->sector_count  = 32;
-		info->size          = 0x00800000;
-		sector_offset = 0x40000;
-		break;				/* => 4x2 MB		*/
-
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		return (0);			/* => no or unknown flash */
-
-	}
-
-	/* set up sector start address table */
-	for (i = 0; i < info->sector_count; i++) {
-		info->start[i] = base;
-		base += sector_offset;
-		/* don't know how to check sector protection */
-		info->protect[i] = 0;
-	}
-
-	/*
-	 * Prevent writes to uninitialized FLASH.
-	 */
-	if (info->flash_id != FLASH_UNKNOWN) {
-		addr = (vu_long *)info->start[0];
-		*addr = 0xFFFFFF;	/* reset bank to read array mode */
-		asm("sync");
-	}
-
-	return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int	flash_erase (flash_info_t *info, int s_first, int s_last)
-{
-	int flag, prot, sect;
-	ulong start, now, last;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	if (    ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_INTEL)
-	     && ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_SHARP) ) {
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-			info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect=s_first; sect<=s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	} else {
-		printf ("\n");
-	}
-
-#ifdef DEBUG
-	printf("\nFlash Erase:\n");
-#endif
-	/* Make Sure Block Lock Bit is not set. */
-	if(clear_block_lock_bit((vu_long *)(info->start[s_first]))){
-		return 1;
-	}
-
-	/* Start erase on unprotected sectors */
-#if defined(DEBUG)
-	printf("Begin to erase now,s_first=0x%x s_last=0x%x...\n",s_first,s_last);
-#endif
-	for (sect = s_first; sect<=s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			vu_long *addr = (vu_long *)(info->start[sect]);
-			asm("sync");
-
-			last = start = get_timer (0);
-
-			/* Disable interrupts which might cause a timeout here */
-			flag = disable_interrupts();
-
-			/* Reset Array */
-			*addr = 0xffffffff;
-			asm("sync");
-			/* Clear Status Register */
-			*addr = 0x50505050;
-			asm("sync");
-			/* Single Block Erase Command */
-			*addr = 0x20202020;
-			asm("sync");
-			/* Confirm */
-			*addr = 0xD0D0D0D0;
-			asm("sync");
-
-			if((info->flash_id & FLASH_TYPEMASK) != FLASH_LH28F016SCT) {
-			    /* Resume Command, as per errata update */
-			    *addr = 0xD0D0D0D0;
-			    asm("sync");
-			}
-
-			/* re-enable interrupts if necessary */
-			if (flag)
-				enable_interrupts();
-
-			/* wait at least 80us - let's wait 1 ms */
-			udelay (1000);
-			while ((*addr & 0x00800080) != 0x00800080) {
-				if(*addr & 0x00200020){
-					printf("Error in Block Erase - Lock Bit may be set!\n");
-					printf("Status Register = 0x%X\n", (uint)*addr);
-					*addr = 0xFFFFFFFF;	/* reset bank */
-					asm("sync");
-					return 1;
-				}
-				if ((now=get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-					printf ("Timeout\n");
-					*addr = 0xFFFFFFFF;	/* reset bank */
-					asm("sync");
-					return 1;
-				}
-				/* show that we're waiting */
-				if ((now - last) > 1000) {	/* every second */
-					putc ('.');
-					last = now;
-				}
-			}
-
-			/* reset to read mode */
-			*addr = 0xFFFFFFFF;
-			asm("sync");
-		}
-	}
-
-	printf ("flash erase done\n");
-	return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-	ulong cp, wp, data;
-	int i, l, rc;
-
-	wp = (addr & ~3);	/* get lower word aligned address */
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i=0, cp=wp; i<l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-		for (; i<4 && cnt>0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt==0 && i<4; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-
-		if ((rc = write_word(info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp += 4;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	while (cnt >= 4) {
-		data = 0;
-		for (i=0; i<4; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_word(info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp  += 4;
-		cnt -= 4;
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i<4; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *)cp);
-	}
-
-	return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
-	vu_long *addr = (vu_long *)dest;
-	ulong start, csr;
-	int flag;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*addr & data) != data) {
-		return (2);
-	}
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	/* Write Command */
-	*addr = 0x10101010;
-	asm("sync");
-
-	/* Write Data */
-	*addr = data;
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	/* data polling for D7 */
-	start = get_timer (0);
-	flag  = 0;
-
-	while (((csr = *addr) & 0x00800080) != 0x00800080) {
-		if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
-			flag = 1;
-			break;
-		}
-	}
-	if (csr & 0x40404040) {
-		printf ("CSR indicates write error (%08lx) at %08lx\n", csr, (ulong)addr);
-		flag = 1;
-	}
-
-	/* Clear Status Registers Command */
-	*addr = 0x50505050;
-	asm("sync");
-	/* Reset to read array mode */
-	*addr = 0xFFFFFFFF;
-	asm("sync");
-
-	return (flag);
-}
-
-/*-----------------------------------------------------------------------
- * Clear Block Lock Bit, returns:
- * 0 - OK
- * 1 - Timeout
- */
-
-static int clear_block_lock_bit(vu_long  * addr)
-{
-	ulong start, now;
-
-	/* Reset Array */
-	*addr = 0xffffffff;
-	asm("sync");
-	/* Clear Status Register */
-	*addr = 0x50505050;
-	asm("sync");
-
-	*addr = 0x60606060;
-	asm("sync");
-	*addr = 0xd0d0d0d0;
-	asm("sync");
-
-	start = get_timer (0);
-	while((*addr & 0x00800080) != 0x00800080){
-		if ((now=get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-			printf ("Timeout on clearing Block Lock Bit\n");
-			*addr = 0xFFFFFFFF;	/* reset bank */
-			asm("sync");
-			return 1;
-		}
-	}
-	return 0;
-}
-
-#endif /* !CFG_NO_FLASH */

+ 0 - 537
board/mpc8560ads/flash.c

@@ -1,537 +0,0 @@
-/*
- * (C) Copyright 2003 Motorola Inc.
- *  Xianghua Xiao,(X.Xiao@motorola.com)
- *
- * (C) Copyright 2000, 2001
- *  Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2001, Stuart Hughes, Lineo Inc, stuarth@lineo.com
- * Add support the Sharp chips on the mpc8260ads.
- * I started with board/ip860/flash.c and made changes I found in
- * the MTD project by David Schleef.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-#if !defined(CFG_NO_FLASH)
-
-flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
-
-#if defined(CFG_ENV_IS_IN_FLASH)
-# ifndef  CFG_ENV_ADDR
-#  define CFG_ENV_ADDR	(CFG_FLASH_BASE + CFG_ENV_OFFSET)
-# endif
-# ifndef  CFG_ENV_SIZE
-#  define CFG_ENV_SIZE	CFG_ENV_SECT_SIZE
-# endif
-# ifndef  CFG_ENV_SECT_SIZE
-#  define CFG_ENV_SECT_SIZE  CFG_ENV_SIZE
-# endif
-#endif
-
-#undef DEBUG
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_long *addr, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-static int clear_block_lock_bit(vu_long * addr);
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-	unsigned long size;
-	int i;
-
-	/* Init: enable write,
-	 * or we cannot even write flash commands
-	 */
-	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
-		flash_info[i].flash_id = FLASH_UNKNOWN;
-
-		/* set the default sector offset */
-	}
-
-	/* Static FLASH Bank configuration here - FIXME XXX */
-
-	size = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]);
-
-	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
-		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
-			size, size<<20);
-	}
-
-	/* Re-do sizing to get full correct info */
-	size = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]);
-
-	flash_info[0].size = size;
-
-#if CFG_MONITOR_BASE >= CFG_FLASH_BASE
-	/* monitor protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+monitor_flash_len-1,
-		      &flash_info[0]);
-
-#ifdef	CFG_ENV_IS_IN_FLASH
-	/* ENV protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CFG_ENV_ADDR,
-		      CFG_ENV_ADDR+CFG_ENV_SECT_SIZE-1,
-		      &flash_info[0]);
-#endif
-#endif
-	return (size);
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info  (flash_info_t *info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_INTEL:	printf ("Intel ");		break;
-	case FLASH_MAN_SHARP:   printf ("Sharp ");		break;
-	default:		printf ("Unknown Vendor ");	break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_28F016SV:	printf ("28F016SV (16 Mbit, 32 x 64k)\n");
-				break;
-	case FLASH_28F160S3:	printf ("28F160S3 (16 Mbit, 32 x 512K)\n");
-				break;
-	case FLASH_28F320S3:	printf ("28F320S3 (32 Mbit, 64 x 512K)\n");
-				break;
-	case FLASH_LH28F016SCT: printf ("28F016SC (16 Mbit, 32 x 64K)\n");
-				break;
-	case FLASH_28F640J3A:   printf ("28F640J3A (64 Mbit, 64 x 128K)\n");
-				break;
-	default:		printf ("Unknown Chip Type\n");
-				break;
-	}
-
-	printf ("  Size: %ld MB in %d Sectors\n",
-		info->size >> 20, info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-	for (i=0; i<info->sector_count; ++i) {
-		if ((i % 5) == 0)
-			printf ("\n   ");
-		printf (" %08lX%s",
-			info->start[i],
-			info->protect[i] ? " (RO)" : "     "
-		);
-	}
-	printf ("\n");
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info)
-{
-	short i;
-	ulong value;
-	ulong base = (ulong)addr;
-	ulong sector_offset;
-
-#ifdef DEBUG
-	printf("Check flash at 0x%08x\n",(uint)addr);
-#endif
-	/* Write "Intelligent Identifier" command: read Manufacturer ID */
-	*addr = 0x90909090;
-	udelay(20);
-	asm("sync");
-
-	value = addr[0] & 0x00FF00FF;
-
-#ifdef DEBUG
-	printf("manufacturer=0x%x\n",(uint)value);
-#endif
-	switch (value) {
-	case MT_MANUFACT:	/* SHARP, MT or => Intel */
-	case INTEL_ALT_MANU:
-		info->flash_id = FLASH_MAN_INTEL;
-		break;
-	default:
-		printf("unknown manufacturer: %x\n", (unsigned int)value);
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		return (0);			/* no or unknown flash	*/
-	}
-
-	value = addr[1] & 0x00FF00FF;             /* device ID            */
-
-#ifdef DEBUG
-	printf("deviceID=0x%x\n",(uint)value);
-#endif
-	switch (value) {
-	case (INTEL_ID_28F016S):
-		info->flash_id += FLASH_28F016SV;
-		info->sector_count = 32;
-		info->size = 0x00400000;
-		sector_offset = 0x20000;
-		break;				/* => 2x2 MB		*/
-
-	case (INTEL_ID_28F160S3):
-		info->flash_id += FLASH_28F160S3;
-		info->sector_count = 32;
-		info->size = 0x00400000;
-		sector_offset = 0x20000;
-		break;				/* => 2x2 MB		*/
-
-	case (INTEL_ID_28F320S3):
-		info->flash_id += FLASH_28F320S3;
-		info->sector_count = 64;
-		info->size = 0x00800000;
-		sector_offset = 0x20000;
-		break;				/* => 2x4 MB		*/
-
-	case (INTEL_ID_28F640J3A):
-		info->flash_id += FLASH_28F640J3A;
-		info->sector_count = 64;
-		info->size = 0x01000000;
-		sector_offset = 0x40000;
-		break;                          /* => 8 MB             */
-
-	case SHARP_ID_28F016SCL:
-	case SHARP_ID_28F016SCZ:
-		info->flash_id      = FLASH_MAN_SHARP | FLASH_LH28F016SCT;
-		info->sector_count  = 32;
-		info->size          = 0x00800000;
-		sector_offset = 0x40000;
-		break;				/* => 4x2 MB		*/
-
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		return (0);			/* => no or unknown flash */
-
-	}
-
-	/* set up sector start address table */
-	for (i = 0; i < info->sector_count; i++) {
-		info->start[i] = base;
-		base += sector_offset;
-		/* don't know how to check sector protection */
-		info->protect[i] = 0;
-	}
-
-	/*
-	 * Prevent writes to uninitialized FLASH.
-	 */
-	if (info->flash_id != FLASH_UNKNOWN) {
-		addr = (vu_long *)info->start[0];
-		*addr = 0xFFFFFF;	/* reset bank to read array mode */
-		asm("sync");
-	}
-
-	return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int	flash_erase (flash_info_t *info, int s_first, int s_last)
-{
-	int flag, prot, sect;
-	ulong start, now, last;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	if (    ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_INTEL)
-	     && ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_SHARP) ) {
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-			info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect=s_first; sect<=s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	} else {
-		printf ("\n");
-	}
-
-#ifdef DEBUG
-	printf("\nFlash Erase:\n");
-#endif
-	/* Make Sure Block Lock Bit is not set. */
-	if(clear_block_lock_bit((vu_long *)(info->start[s_first]))){
-		return 1;
-	}
-
-	/* Start erase on unprotected sectors */
-#if defined(DEBUG)
-	printf("Begin to erase now,s_first=0x%x s_last=0x%x...\n",s_first,s_last);
-#endif
-	for (sect = s_first; sect<=s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			vu_long *addr = (vu_long *)(info->start[sect]);
-			asm("sync");
-
-			last = start = get_timer (0);
-
-			/* Disable interrupts which might cause a timeout here */
-			flag = disable_interrupts();
-
-			/* Reset Array */
-			*addr = 0xffffffff;
-			asm("sync");
-			/* Clear Status Register */
-			*addr = 0x50505050;
-			asm("sync");
-			/* Single Block Erase Command */
-			*addr = 0x20202020;
-			asm("sync");
-			/* Confirm */
-			*addr = 0xD0D0D0D0;
-			asm("sync");
-
-			if((info->flash_id & FLASH_TYPEMASK) != FLASH_LH28F016SCT) {
-			    /* Resume Command, as per errata update */
-			    *addr = 0xD0D0D0D0;
-			    asm("sync");
-			}
-
-			/* re-enable interrupts if necessary */
-			if (flag)
-				enable_interrupts();
-
-			/* wait at least 80us - let's wait 1 ms */
-			udelay (1000);
-			while ((*addr & 0x00800080) != 0x00800080) {
-				if(*addr & 0x00200020){
-					printf("Error in Block Erase - Lock Bit may be set!\n");
-					printf("Status Register = 0x%X\n", (uint)*addr);
-					*addr = 0xFFFFFFFF;	/* reset bank */
-					asm("sync");
-					return 1;
-				}
-				if ((now=get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-					printf ("Timeout\n");
-					*addr = 0xFFFFFFFF;	/* reset bank */
-					asm("sync");
-					return 1;
-				}
-				/* show that we're waiting */
-				if ((now - last) > 1000) {	/* every second */
-					putc ('.');
-					last = now;
-				}
-			}
-
-			/* reset to read mode */
-			*addr = 0xFFFFFFFF;
-			asm("sync");
-		}
-	}
-
-	printf ("flash erase done\n");
-	return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-	ulong cp, wp, data;
-	int i, l, rc;
-
-	wp = (addr & ~3);	/* get lower word aligned address */
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i=0, cp=wp; i<l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-		for (; i<4 && cnt>0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt==0 && i<4; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-
-		if ((rc = write_word(info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp += 4;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	while (cnt >= 4) {
-		data = 0;
-		for (i=0; i<4; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_word(info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp  += 4;
-		cnt -= 4;
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i<4; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *)cp);
-	}
-
-	return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
-	vu_long *addr = (vu_long *)dest;
-	ulong start, csr;
-	int flag;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*addr & data) != data) {
-		return (2);
-	}
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	/* Write Command */
-	*addr = 0x10101010;
-	asm("sync");
-
-	/* Write Data */
-	*addr = data;
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	/* data polling for D7 */
-	start = get_timer (0);
-	flag  = 0;
-
-	while (((csr = *addr) & 0x00800080) != 0x00800080) {
-		if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
-			flag = 1;
-			break;
-		}
-	}
-	if (csr & 0x40404040) {
-		printf ("CSR indicates write error (%08lx) at %08lx\n", csr, (ulong)addr);
-		flag = 1;
-	}
-
-	/* Clear Status Registers Command */
-	*addr = 0x50505050;
-	asm("sync");
-	/* Reset to read array mode */
-	*addr = 0xFFFFFFFF;
-	asm("sync");
-
-	return (flag);
-}
-
-/*-----------------------------------------------------------------------
- * Clear Block Lock Bit, returns:
- * 0 - OK
- * 1 - Timeout
- */
-
-static int clear_block_lock_bit(vu_long  * addr)
-{
-	ulong start, now;
-
-	/* Reset Array */
-	*addr = 0xffffffff;
-	asm("sync");
-	/* Clear Status Register */
-	*addr = 0x50505050;
-	asm("sync");
-
-	*addr = 0x60606060;
-	asm("sync");
-	*addr = 0xd0d0d0d0;
-	asm("sync");
-
-	start = get_timer (0);
-	while((*addr & 0x00800080) != 0x00800080){
-		if ((now=get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-			printf ("Timeout on clearing Block Lock Bit\n");
-			*addr = 0xFFFFFFFF;	/* reset bank */
-			asm("sync");
-			return 1;
-		}
-	}
-	return 0;
-}
-
-#endif /* !CFG_NO_FLASH */

+ 14 - 5
common/cmd_bdinfo.c

@@ -79,24 +79,33 @@ int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 #endif
 	print_str ("busfreq",	    strmhz(buf, bd->bi_busfreq));
 #endif /* CONFIG_405GP, CONFIG_405CR, CONFIG_405EP, CONFIG_XILINX_ML300 */
+
 	puts ("ethaddr     =");
 	for (i=0; i<6; ++i) {
 		printf ("%c%02X", i ? ':' : ' ', bd->bi_enetaddr[i]);
 	}
-#if (defined CONFIG_PN62) || (defined CONFIG_PPCHAMELEONEVB) || \
-    (defined CONFIG_MPC8540ADS) || (defined CONFIG_MPC8560ADS) || \
-    (defined CONFIG_MPC8555CDS)
+
+#if defined(CONFIG_ETH1ADDR)
 	puts ("\neth1addr    =");
 	for (i=0; i<6; ++i) {
 		printf ("%c%02X", i ? ':' : ' ', bd->bi_enet1addr[i]);
 	}
-#endif /* CONFIG_PN62 */
-#if defined(CONFIG_MPC8540ADS) || defined(CONFIG_MPC8560ADS) || defined(CONFIG_MPC8555CDS)
+#endif
+
+#if defined(CONFIG_ETH2ADDR)
        puts ("\neth2addr    =");
        for (i=0; i<6; ++i) {
 		printf ("%c%02X", i ? ':' : ' ', bd->bi_enet2addr[i]);
 	}
 #endif
+
+#if defined(CONFIG_ETH3ADDR)
+       puts ("\neth3addr    =");
+       for (i=0; i<6; ++i) {
+		printf ("%c%02X", i ? ':' : ' ', bd->bi_enet3addr[i]);
+	}
+#endif
+
 #ifdef CONFIG_HERMES
 	print_str ("ethspeed",	    strmhz(buf, bd->bi_ethspeed));
 #endif

+ 3 - 3
doc/README.mpc85xxads

@@ -7,7 +7,7 @@ Updated 13-July-2004 Jon Loeliger
 0. Toolchain
 
     The Binutils in current ELDK toolchain will not support MPC85xx
-    chip.  You need use the newest binutils-2.14.tar.bz2 from
+    chip.  You need to use binutils-2.14.tar.bz2 (or newer) from
     http://ftp.gnu.org/gnu/binutils.
 
     The 8540/8560 ADS code base is known to compile using:
@@ -191,10 +191,10 @@ straightforward.
 
 4.4 Reflash U-boot Image using U-boot
 
-    => tftp 0 u-boot.bin
+    => tftp 10000 u-boot.bin
     => protect off fff80000 ffffffff
     => erase fff80000 ffffffff
-    => cp.b 0 fff80000 80000
+    => cp.b 10000 fff80000 80000
 
 
 4.5 Reflash U-Boot with a BDI-2000

+ 187 - 0
doc/README.mpc85xxcds

@@ -0,0 +1,187 @@
+Motorola MPC85xxCDS boards
+--------------------------
+
+The CDS family of boards consists of a PCI backplane called the
+"Arcadia", a PCI-form-factor carrier card that plugs into a PCI slot,
+and a CPU daughter card that bolts onto the daughter card.
+
+Much of the content of the README.mpc85xxads for the 85xx ADS boards
+applies to the 85xx CDS boards as well.  In particular the toolchain,
+the switch nomenclature, and the basis for the memory map.  There are
+some differences, though.
+
+
+Building U-Boot
+---------------
+
+The Binutils in current ELDK toolchain will not support MPC85xx
+chip.  You need to use binutils-2.14.tar.bz2 (or newer) from
+    http://ftp.gnu.org/gnu/binutils.
+
+The 85xx CDS code base is known to compile using:
+    gcc (GCC) 3.2.2 20030217 (Yellow Dog Linux 3.0 3.2.2-2a)
+
+
+Memory Map
+----------
+
+The memory map for u-boot and linux has been extended w.r.t. the ADS
+platform to allow for utilization of all 85xx CDS devices.  The memory
+map is setup for linux to operate properly.  The linux source when
+configured for MPC85xx CDS has been updated to reflect the new memory
+map.
+
+The mapping is:
+
+   0x0000_0000     0x7fff_ffff     DDR                     2G
+   0x8000_0000     0x9fff_ffff     PCI1 MEM                512M
+   0xa000_0000     0xbfff_ffff     PCI2 MEM                512M
+   0xe000_0000     0xe00f_ffff     CCSR                    1M
+   0xe200_0000     0xe2ff_ffff     PCI1 IO                 16M
+   0xe300_0000     0xe3ff_ffff     PCI2 IO                 16M
+   0xf000_0000     0xf7ff_ffff     SDRAM                   128M
+   0xf800_0000     0xf80f_ffff     NVRAM/CADMUS (*)        1M
+   0xff00_0000     0xff7f_ffff     FLASH (2nd bank)        8M
+   0xff80_0000     0xffff_ffff     FLASH (boot bank)       8M
+
+   (*) The system control registers (CADMUS) start at offset 0xfdb0_4000
+   within the NVRAM/CADMUS region of memory.
+
+
+Using Flash
+-----------
+
+The CDS board  has two flash banks, each 8MB in size (2^23 = 0x00800000).
+There is a switch which allows the boot-bank to be selected.  The switch
+settings for updating flash are given below.
+
+The u-boot commands for copying the boot-bank into the secondary bank are
+as follows:
+
+     erase ff780000 ff7fffff
+     cp.b fff80000 ff780000 80000
+
+
+U-boot/kermit commands for downloading an image, then copying
+it into the secondary bank:
+
+     loadb
+     [Drop to kermit:
+        ^\c
+        send <u-boot-bin-image>
+        c
+     ]
+
+     erase ff780000 ff7fffff
+     cp.b $loadaddr ff780000 80000
+
+
+U-boot commands for downloading an image via tftp and flashing
+it into the second bank:
+
+     tftp 10000 <u-boot.bin.image>
+     erase ff780000 ff7fffff
+     cp.b 10000 ff780000 80000
+
+
+After copying the image into the second bank of flash, be sure to toggle
+SW2[2] on the carrier card before resetting the board in order to set the
+secondary bank as the boot-bank.
+
+
+Carrier Board Switches
+----------------------
+
+As a reminder, you should read the README.mpc85xxads too.
+
+Most switches on the carrier board should not be changed.  The only
+user-settable switches on the carrier board are used to configure
+the flash banks and determining the PCI slot.
+
+The first two bits of SW2 control how flash is used on the board:
+
+      12345678
+      --------
+  SW2=00XXXXXX     FLASH:  Boot bank 1, bank 2 available.
+      01XXXXXX     FLASH:  Boot bank 2, bank 1 available (swapped).
+      10XXXXXX     FLASH:  Boot promjet, bank 1 available
+      11XXXXXX     FLASH:  Boot promjet, bank 2 available
+
+The boot bank is always mapped to FF80_0000 and listed first by
+the "flinfo" command.  The secondary bank is always FF00_0000.
+
+When using PCI, linux needs to know to which slot the CDS carrier is
+connected..  By convention, the user-specific bits of SW2 are used to
+convey this information:
+
+      12345678
+      --------
+  SW2=xxxxxx00     PCI SLOT INFORM: The CDS carrier is in slot0 of the Arcadia
+      xxxxxx01     PCI SLOT INFORM: The CDS carrier is in slot1 of the Arcadia
+      xxxxxx10     PCI SLOT INFORM: The CDS carrier is in slot2 of the Arcadia
+      xxxxxx11     PCI SLOT INFORM: The CDS carrier is in slot3 of the Arcadia
+
+These are cleverly, er, clearly silkscreened as Slot 1 through 4,
+respectively, on the Arcadia near the support posts.
+
+
+The default setting of all switches on the carrier board is:
+
+      12345678
+      --------
+  SW1=01101100
+  SW2=0x1111yy     x=Flash bank, yy=PCI slot
+  SW3=11101111
+  SW4=10001000
+
+
+CPU Card Switches
+-----------------
+
+Most switches on the CPU Card should not be changed.  However, the
+frequency can be changed by setting SW3:
+
+      12345678
+      --------
+  SW3=XX00XXXX == CORE:CCB 2:1
+      XX01XXXX == CORE:CCB 5:2
+      XX10XXXX == CORE:CCB 3:1
+      XX11XXXX == CORE:CCB 7:2
+      XXXX1000 == CCB:SYSCLK 8:1
+      XXXX1010 == CCB:SYSCLK 10:1
+
+A safe default setting for all switches on the CPU board is:
+
+      12345678
+      --------
+  SW1=10001111
+  SW2=01000111
+  SW3=00001000
+  SW4=11111110
+
+
+eDINK Info
+----------
+
+One bank of flash may contain an eDINK image.
+
+Memory Map:
+
+   CCSRBAR @ 0xe0000000
+   Flash Bank 1 @ 0xfe000000
+   Flash Bank 2 @ 0xff000000
+   Ram @ 0
+
+Commands for downloading a u-boot image to memory from edink:
+
+   env -c
+   time -s 4/8/2004 4:30p
+   dl -k -b -o 100000
+   [Drop to kermit:
+        ^\c
+        transmit /binary <u-boot-bin-image>
+        c
+   ]
+
+   fu -l 100000 fe780000 80000
+

+ 6 - 2
include/asm-ppc/immap_85xx.h

@@ -156,7 +156,9 @@ typedef struct ccsr_i2c {
 	char	res6[4075];
 } ccsr_i2c_t;
 
-#if defined (CONFIG_MPC8540) || defined (CONFIG_MPC8555)
+#if defined(CONFIG_MPC8540) \
+	|| defined(CONFIG_MPC8541) \
+	|| defined(CONFIG_MPC8555)
 /* DUART Registers(0x4000-0x5000) */
 typedef struct ccsr_duart {
 	char	res1[1280];
@@ -1021,7 +1023,9 @@ typedef struct ccsr_pic {
 } ccsr_pic_t;
 
 /* CPM Block(0x8_0000-0xc_0000) */
-#if defined (CONFIG_MPC8540) || defined (CONFIG_MPC8555)
+#if defined(CONFIG_MPC8540) \
+	|| defined(CONFIG_MPC8541) \
+	|| defined(CONFIG_MPC8555)
 typedef struct ccsr_cpm {
 	char res[262144];
 } ccsr_cpm_t;

+ 5 - 13
include/asm-ppc/u-boot.h

@@ -77,27 +77,19 @@ typedef struct bd_info {
 #if defined(CONFIG_HYMOD)
 	hymod_conf_t	bi_hymod_conf;	/* hymod configuration information */
 #endif
-#if defined(CFG_GT_6426x)		|| \
-    defined(CONFIG_PN62)		|| \
-    defined(CONFIG_PPCHAMELEONEVB)	|| \
-    defined(CONFIG_SXNI855T)		|| \
-    defined(CONFIG_SVM_SC8xx)		|| \
-    defined(CONFIG_MPC8540ADS)          || \
-    defined(CONFIG_MPC8555CDS)		|| \
-    defined(CONFIG_MPC8560ADS)		|| \
-    defined(CONFIG_440_GX)
+
+#if defined(CONFIG_ETH1ADDR)
 	/* second onboard ethernet port */
 	unsigned char   bi_enet1addr[6];
 #endif
-#if defined(CFG_GT_6426x) || defined(CONFIG_SVM_SC8xx) || \
-    defined(CONFIG_MPC8540ADS) || defined(CONFIG_MPC8560ADS) || \
-    defined(CONFIG_MPC8555CDS) || defined(CONFIG_440_GX)
+#if defined(CONFIG_ETH2ADDR)
 	/* third onboard ethernet port */
 	unsigned char	bi_enet2addr[6];
 #endif
-#if defined(CONFIG_440_GX)
+#if defined(CONFIG_ETH3ADDR)
 	unsigned char   bi_enet3addr[6];
 #endif
+
 #if defined(CONFIG_405GP) || defined(CONFIG_405EP) || defined (CONFIG_440_GX)
 	unsigned int	bi_opbfreq;		/* OPB clock in Hz */
 	int		bi_iic_fast[2];		/* Use fast i2c mode */

+ 474 - 0
include/configs/MPC8541CDS.h

@@ -0,0 +1,474 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * mpc8541cds board configuration file
+ *
+ * Please refer to doc/README.mpc85xxcds for more info.
+ *
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		1	/* BOOKE */
+#define CONFIG_E500		1	/* BOOKE e500 family */
+#define CONFIG_MPC85xx		1	/* MPC8540/60/55/41 */
+#define CONFIG_MPC8541		1	/* MPC8541 specific */
+#define CONFIG_MPC8541CDS	1	/* MPC8541CDS board specific */
+
+#define CONFIG_PCI
+#define CONFIG_TSEC_ENET 		/* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_DDR_DLL			/* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
+
+/*
+ * When initializing flash, if we cannot find the manufacturer ID,
+ * assume this is the AMD flash associated with the CDS board.
+ * This allows booting from a promjet.
+ */
+#define CONFIG_ASSUME_AMD_FLASH
+
+#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_clock_freq(void);
+#endif
+#define CONFIG_SYS_CLK_FREQ	get_clock_freq() /* sysclk for MPC85xx */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE		    	    /* toggle L2 cache 	*/
+#define CONFIG_BTB			    /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING		    /* toggle addr streaming   */
+
+#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
+
+#undef	CFG_DRAM_TEST			/* memory test, takes time */
+#define CFG_MEMTEST_START	0x00200000	/* memtest works on */
+#define CFG_MEMTEST_END		0x00400000
+
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default */
+#define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
+#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
+
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+
+#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+
+/*
+ * Make sure required options are set
+ */
+#ifndef CONFIG_SPD_EEPROM
+#error ("CONFIG_SPD_EEPROM is required by MPC85555CDS")
+#endif
+
+
+
+/*
+ * SDRAM on the Local Bus
+ */
+#define CFG_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
+#define CFG_FLASH_BASE		0xff000000	/* start of FLASH 8M */
+
+#define CFG_BR0_PRELIM		0xff801001	/* port size 16bit */
+#define CFG_BR1_PRELIM		0xff001001	/* port size 16bit */
+
+#define	CFG_OR0_PRELIM		0xff806e61	/* 8MB Flash */
+#define	CFG_OR1_PRELIM		0xff806e61	/* 8MB Flash */
+
+#define CFG_FLASH_BANKS_LIST	{0xff800000, CFG_FLASH_BASE}
+#define CFG_MAX_FLASH_BANKS	2		/* number of banks */
+#define CFG_MAX_FLASH_SECT	128		/* sectors per device */
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor */
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+/*
+ * Local Bus Definitions
+ */
+
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ *    port-size = 32-bits = BR2[19:20] = 11
+ *    no parity checking = BR2[21:22] = 00
+ *    SDRAM for MSEL = BR2[24:26] = 011
+ *    Valid = BR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
+ *
+ * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * FIXME: the top 17 bits of BR2.
+ */
+
+#define CFG_BR2_PRELIM          0xf0001861
+
+/*
+ * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ *
+ * For OR2, need:
+ *    64MB mask for AM, OR2[0:7] = 1111 1100
+ *		   XAM, OR2[17:18] = 11
+ *    9 columns OR2[19-21] = 010
+ *    13 rows   OR2[23-25] = 100
+ *    EAD set for extra time OR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
+ */
+
+#define CFG_OR2_PRELIM		0xfc006901
+
+#define CFG_LBC_LCRR		0x00030004    /* LB clock ratio reg */
+#define CFG_LBC_LBCR		0x00000000    /* LB config reg */
+#define CFG_LBC_LSRT		0x20000000  /* LB sdram refresh timer */
+#define CFG_LBC_MRTPR		0x00000000  /* LB refresh timer prescal*/
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_RFEN	(1 << (31 -  1))
+#define CFG_LBC_LSDMR_BSMA1516	(3 << (31 - 10))
+#define CFG_LBC_LSDMR_BSMA1617	(4 << (31 - 10))
+#define CFG_LBC_LSDMR_RFCR16	(7 << (31 - 16))
+#define CFG_LBC_LSDMR_PRETOACT7	(7 << (31 - 19))
+#define CFG_LBC_LSDMR_ACTTORW7	(7 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW6	(6 << (31 - 22))
+#define CFG_LBC_LSDMR_BL8	(1 << (31 - 23))
+#define CFG_LBC_LSDMR_WRC4	(0 << (31 - 27))
+#define CFG_LBC_LSDMR_CL3	(3 << (31 - 31))
+
+#define CFG_LBC_LSDMR_OP_NORMAL	(0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH	(1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH	(2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW	(3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH	(4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL	(5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK	(6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV	(7 << (31 - 4))
+
+/*
+ * Common settings for all Local Bus SDRAM commands.
+ * At run time, either BSMA1516 (for CPU 1.1)
+ *                  or BSMA1617 (for CPU 1.0) (old)
+ * is OR'ed in too.
+ */
+#define CFG_LBC_LSDMR_COMMON	( CFG_LBC_LSDMR_RFCR16		\
+				| CFG_LBC_LSDMR_PRETOACT7	\
+				| CFG_LBC_LSDMR_ACTTORW7	\
+				| CFG_LBC_LSDMR_BL8		\
+				| CFG_LBC_LSDMR_WRC4		\
+				| CFG_LBC_LSDMR_CL3		\
+				| CFG_LBC_LSDMR_RFEN		\
+				)
+
+/*
+ * The CADMUS registers are connected to CS3 on CDS.
+ * The new memory map places CADMUS at 0xf8000000.
+ *
+ * For BR3, need:
+ *    Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
+ *    port-size = 8-bits  = BR[19:20] = 01
+ *    no parity checking  = BR[21:22] = 00
+ *    GPMC for MSEL       = BR[24:26] = 000
+ *    Valid               = BR[31]    = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
+ *
+ * For OR3, need:
+ *    1 MB mask for AM,   OR[0:16]  = 1111 1111 1111 0000 0
+ *    disable buffer ctrl OR[19]    = 0
+ *    CSNT                OR[20]    = 1
+ *    ACS                 OR[21:22] = 11
+ *    XACS                OR[23]    = 1
+ *    SCY 15 wait states  OR[24:27] = 1111	max is suboptimal but safe
+ *    SETA                OR[28]    = 0
+ *    TRLX                OR[29]    = 1
+ *    EHTR                OR[30]    = 1
+ *    EAD extra time      OR[31]    = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
+ */
+
+#define CADMUS_BASE_ADDR 0xf8000000
+#define CFG_BR3_PRELIM   0xf8000801
+#define CFG_OR3_PRELIM   0xfff00ff7
+
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 	1
+#define CFG_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
+#define CFG_INIT_RAM_END    	0x4000	    /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE  	128	    /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN	    	(512 * 1024) /* Reserve 512 kB for Mon */
+#define CFG_MALLOC_LEN	    	(128 * 1024)	/* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX     2
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE    1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1        (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2        (CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef  CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* I2C */
+#define CONFIG_HARD_I2C			/* I2C with hardware support */
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_EEPROM_ADDR	0x57
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE	0x80000000
+#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCI1_IO_BASE	0xe2000000
+#define CFG_PCI1_IO_PHYS	CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE	0x1000000	/* 16M */
+
+#define CFG_PCI2_MEM_BASE	0xa0000000
+#define CFG_PCI2_MEM_PHYS	CFG_PCI2_MEM_BASE
+#define CFG_PCI2_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCI2_IO_BASE	0xe3000000
+#define CFG_PCI2_IO_PHYS	CFG_PCI2_IO_BASE
+#define CFG_PCI2_IO_SIZE	0x1000000	/* 16M */
+
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+    #define PCI_ENET0_IOADDR      0xe0000000
+    #define PCI_ENET0_MEMADDR     0xe0000000
+    #define PCI_IDSEL_NUMBER      0x0c 	/*slot0->3(IDSEL)=12->15*/
+#endif
+
+#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
+
+#endif	/* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 	1
+#endif
+
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_MPC85XX_TSEC1	1
+#define CONFIG_MPC85XX_TSEC2	1
+#undef CONFIG_MPC85XX_FEC
+#define TSEC1_PHY_ADDR		0
+#define TSEC2_PHY_ADDR		1
+#define FEC_PHY_ADDR		3
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+#define FEC_PHYIDX		0
+#define CONFIG_ETHPRIME		"MOTO ENET0"
+
+#endif	/* CONFIG_TSEC_ENET */
+
+
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
+#define CFG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
+#define CFG_ENV_SIZE		0x2000
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+#if defined(CONFIG_PCI)
+#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
+				| CFG_CMD_PCI \
+				| CFG_CMD_PING \
+				| CFG_CMD_I2C \
+				| CFG_CMD_MII)
+#else
+#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
+				| CFG_CMD_PING \
+				| CFG_CMD_I2C \
+				| CFG_CMD_MII)
+#endif
+
+
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory	*/
+#define CFG_LOAD_ADDR	0x2000000	/* default load address */
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	(8 << 20) 	/* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE	32768
+#define CFG_CACHELINE_SIZE	32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_ETHADDR   00:E0:0C:00:00:FD
+#define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
+#define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
+#endif
+
+#define CONFIG_IPADDR    192.168.1.253
+
+#define CONFIG_HOSTNAME  unknown
+#define CONFIG_ROOTPATH  /nfsroot
+#define CONFIG_BOOTFILE  your.uImage
+
+#define CONFIG_SERVERIP  192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK   255.255.255.0
+
+#define CONFIG_LOADADDR  200000   /*default location for tftp and bootm*/
+
+#define CONFIG_BOOTDELAY 10       /* -1 disables auto-boot */
+#undef  CONFIG_BOOTARGS           /* the boot command will set bootargs*/
+
+#define CONFIG_BAUDRATE	115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				        \
+   "netdev=eth0\0"                                                      \
+   "consoledev=ttyS1\0"                                                 \
+   "ramdiskaddr=400000\0"                                               \
+   "ramdiskfile=your.ramdisk.u-boot\0"
+
+#define CONFIG_NFSBOOTCOMMAND	                                        \
+   "setenv bootargs root=/dev/nfs rw "                                  \
+      "nfsroot=$serverip:$rootpath "                                    \
+      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+      "console=$consoledev,$baudrate $othbootargs;"                     \
+   "tftp $loadaddr $bootfile;"                                          \
+   "bootm $loadaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+   "setenv bootargs root=/dev/ram rw "                                  \
+      "console=$consoledev,$baudrate $othbootargs;"                     \
+   "tftp $ramdiskaddr $ramdiskfile;"                                    \
+   "tftp $loadaddr $bootfile;"                                          \
+   "bootm $loadaddr $ramdiskaddr"
+
+#define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
+
+
+#endif	/* __CONFIG_H */

+ 474 - 0
include/configs/MPC8555CDS.h

@@ -0,0 +1,474 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * mpc8555cds board configuration file
+ *
+ * Please refer to doc/README.mpc85xxcds for more info.
+ *
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		1	/* BOOKE */
+#define CONFIG_E500		1	/* BOOKE e500 family */
+#define CONFIG_MPC85xx		1	/* MPC8540/60/55/41 */
+#define CONFIG_MPC8555		1	/* MPC8555 specific */
+#define CONFIG_MPC8555CDS	1	/* MPC8555CDS board specific */
+
+#define CONFIG_PCI
+#define CONFIG_TSEC_ENET 		/* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_DDR_DLL			/* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
+
+/*
+ * When initializing flash, if we cannot find the manufacturer ID,
+ * assume this is the AMD flash associated with the CDS board.
+ * This allows booting from a promjet.
+ */
+#define CONFIG_ASSUME_AMD_FLASH
+
+#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_clock_freq(void);
+#endif
+#define CONFIG_SYS_CLK_FREQ	get_clock_freq() /* sysclk for MPC85xx */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE		    	    /* toggle L2 cache 	*/
+#define CONFIG_BTB			    /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING		    /* toggle addr streaming   */
+
+#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
+
+#undef	CFG_DRAM_TEST			/* memory test, takes time */
+#define CFG_MEMTEST_START	0x00200000	/* memtest works on */
+#define CFG_MEMTEST_END		0x00400000
+
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default */
+#define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
+#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
+
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+
+#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+
+/*
+ * Make sure required options are set
+ */
+#ifndef CONFIG_SPD_EEPROM
+#error ("CONFIG_SPD_EEPROM is required by MPC85555CDS")
+#endif
+
+
+
+/*
+ * SDRAM on the Local Bus
+ */
+#define CFG_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
+#define CFG_FLASH_BASE		0xff000000	/* start of FLASH 8M */
+
+#define CFG_BR0_PRELIM		0xff801001	/* port size 16bit */
+#define CFG_BR1_PRELIM		0xff001001	/* port size 16bit */
+
+#define	CFG_OR0_PRELIM		0xff806e61	/* 8MB Flash */
+#define	CFG_OR1_PRELIM		0xff806e61	/* 8MB Flash */
+
+#define CFG_FLASH_BANKS_LIST	{0xff800000, CFG_FLASH_BASE}
+#define CFG_MAX_FLASH_BANKS	2		/* number of banks */
+#define CFG_MAX_FLASH_SECT	128		/* sectors per device */
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor */
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+/*
+ * Local Bus Definitions
+ */
+
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ *    port-size = 32-bits = BR2[19:20] = 11
+ *    no parity checking = BR2[21:22] = 00
+ *    SDRAM for MSEL = BR2[24:26] = 011
+ *    Valid = BR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
+ *
+ * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * FIXME: the top 17 bits of BR2.
+ */
+
+#define CFG_BR2_PRELIM          0xf0001861
+
+/*
+ * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ *
+ * For OR2, need:
+ *    64MB mask for AM, OR2[0:7] = 1111 1100
+ *		   XAM, OR2[17:18] = 11
+ *    9 columns OR2[19-21] = 010
+ *    13 rows   OR2[23-25] = 100
+ *    EAD set for extra time OR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
+ */
+
+#define CFG_OR2_PRELIM		0xfc006901
+
+#define CFG_LBC_LCRR		0x00030004    /* LB clock ratio reg */
+#define CFG_LBC_LBCR		0x00000000    /* LB config reg */
+#define CFG_LBC_LSRT		0x20000000  /* LB sdram refresh timer */
+#define CFG_LBC_MRTPR		0x00000000  /* LB refresh timer prescal*/
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_RFEN	(1 << (31 -  1))
+#define CFG_LBC_LSDMR_BSMA1516	(3 << (31 - 10))
+#define CFG_LBC_LSDMR_BSMA1617	(4 << (31 - 10))
+#define CFG_LBC_LSDMR_RFCR16	(7 << (31 - 16))
+#define CFG_LBC_LSDMR_PRETOACT7	(7 << (31 - 19))
+#define CFG_LBC_LSDMR_ACTTORW7	(7 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW6	(6 << (31 - 22))
+#define CFG_LBC_LSDMR_BL8	(1 << (31 - 23))
+#define CFG_LBC_LSDMR_WRC4	(0 << (31 - 27))
+#define CFG_LBC_LSDMR_CL3	(3 << (31 - 31))
+
+#define CFG_LBC_LSDMR_OP_NORMAL	(0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH	(1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH	(2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW	(3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH	(4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL	(5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK	(6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV	(7 << (31 - 4))
+
+/*
+ * Common settings for all Local Bus SDRAM commands.
+ * At run time, either BSMA1516 (for CPU 1.1)
+ *                  or BSMA1617 (for CPU 1.0) (old)
+ * is OR'ed in too.
+ */
+#define CFG_LBC_LSDMR_COMMON	( CFG_LBC_LSDMR_RFCR16		\
+				| CFG_LBC_LSDMR_PRETOACT7	\
+				| CFG_LBC_LSDMR_ACTTORW7	\
+				| CFG_LBC_LSDMR_BL8		\
+				| CFG_LBC_LSDMR_WRC4		\
+				| CFG_LBC_LSDMR_CL3		\
+				| CFG_LBC_LSDMR_RFEN		\
+				)
+
+/*
+ * The CADMUS registers are connected to CS3 on CDS.
+ * The new memory map places CADMUS at 0xf8000000.
+ *
+ * For BR3, need:
+ *    Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
+ *    port-size = 8-bits  = BR[19:20] = 01
+ *    no parity checking  = BR[21:22] = 00
+ *    GPMC for MSEL       = BR[24:26] = 000
+ *    Valid               = BR[31]    = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
+ *
+ * For OR3, need:
+ *    1 MB mask for AM,   OR[0:16]  = 1111 1111 1111 0000 0
+ *    disable buffer ctrl OR[19]    = 0
+ *    CSNT                OR[20]    = 1
+ *    ACS                 OR[21:22] = 11
+ *    XACS                OR[23]    = 1
+ *    SCY 15 wait states  OR[24:27] = 1111	max is suboptimal but safe
+ *    SETA                OR[28]    = 0
+ *    TRLX                OR[29]    = 1
+ *    EHTR                OR[30]    = 1
+ *    EAD extra time      OR[31]    = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
+ */
+
+#define CADMUS_BASE_ADDR 0xf8000000
+#define CFG_BR3_PRELIM   0xf8000801
+#define CFG_OR3_PRELIM   0xfff00ff7
+
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 	1
+#define CFG_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
+#define CFG_INIT_RAM_END    	0x4000	    /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE  	128	    /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN	    	(512 * 1024) /* Reserve 512 kB for Mon */
+#define CFG_MALLOC_LEN	    	(128 * 1024)	/* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX     2
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE    1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1        (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2        (CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef  CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* I2C */
+#define CONFIG_HARD_I2C			/* I2C with hardware support */
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_EEPROM_ADDR	0x57
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE	0x80000000
+#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCI1_IO_BASE	0xe2000000
+#define CFG_PCI1_IO_PHYS	CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE	0x1000000	/* 16M */
+
+#define CFG_PCI2_MEM_BASE	0xa0000000
+#define CFG_PCI2_MEM_PHYS	CFG_PCI2_MEM_BASE
+#define CFG_PCI2_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCI2_IO_BASE	0xe3000000
+#define CFG_PCI2_IO_PHYS	CFG_PCI2_IO_BASE
+#define CFG_PCI2_IO_SIZE	0x1000000	/* 16M */
+
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+    #define PCI_ENET0_IOADDR      0xe0000000
+    #define PCI_ENET0_MEMADDR     0xe0000000
+    #define PCI_IDSEL_NUMBER      0x0c 	/*slot0->3(IDSEL)=12->15*/
+#endif
+
+#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
+
+#endif	/* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 	1
+#endif
+
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_MPC85XX_TSEC1	1
+#define CONFIG_MPC85XX_TSEC2	1
+#undef CONFIG_MPC85XX_FEC
+#define TSEC1_PHY_ADDR		0
+#define TSEC2_PHY_ADDR		1
+#define FEC_PHY_ADDR		3
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+#define FEC_PHYIDX		0
+#define CONFIG_ETHPRIME		"MOTO ENET0"
+
+#endif	/* CONFIG_TSEC_ENET */
+
+
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
+#define CFG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
+#define CFG_ENV_SIZE		0x2000
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+#if defined(CONFIG_PCI)
+#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
+				| CFG_CMD_PCI \
+				| CFG_CMD_PING \
+				| CFG_CMD_I2C \
+				| CFG_CMD_MII)
+#else
+#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
+				| CFG_CMD_PING \
+				| CFG_CMD_I2C \
+				| CFG_CMD_MII)
+#endif
+
+
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory	*/
+#define CFG_LOAD_ADDR	0x2000000	/* default load address */
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	(8 << 20) 	/* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE	32768
+#define CFG_CACHELINE_SIZE	32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_ETHADDR   00:E0:0C:00:00:FD
+#define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
+#define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
+#endif
+
+#define CONFIG_IPADDR    192.168.1.253
+
+#define CONFIG_HOSTNAME  unknown
+#define CONFIG_ROOTPATH  /nfsroot
+#define CONFIG_BOOTFILE  your.uImage
+
+#define CONFIG_SERVERIP  192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK   255.255.255.0
+
+#define CONFIG_LOADADDR  200000   /*default location for tftp and bootm*/
+
+#define CONFIG_BOOTDELAY 10       /* -1 disables auto-boot */
+#undef  CONFIG_BOOTARGS           /* the boot command will set bootargs*/
+
+#define CONFIG_BAUDRATE	115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				        \
+   "netdev=eth0\0"                                                      \
+   "consoledev=ttyS1\0"                                                 \
+   "ramdiskaddr=400000\0"                                               \
+   "ramdiskfile=your.ramdisk.u-boot\0"
+
+#define CONFIG_NFSBOOTCOMMAND	                                        \
+   "setenv bootargs root=/dev/nfs rw "                                  \
+      "nfsroot=$serverip:$rootpath "                                    \
+      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+      "console=$consoledev,$baudrate $othbootargs;"                     \
+   "tftp $loadaddr $bootfile;"                                          \
+   "bootm $loadaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+   "setenv bootargs root=/dev/ram rw "                                  \
+      "console=$consoledev,$baudrate $othbootargs;"                     \
+   "tftp $ramdiskaddr $ramdiskfile;"                                    \
+   "tftp $loadaddr $bootfile;"                                          \
+   "bootm $loadaddr $ramdiskaddr"
+
+#define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
+
+
+#endif	/* __CONFIG_H */

+ 3 - 7
lib_ppc/board.c

@@ -779,9 +779,7 @@ void board_init_r (gd_t *id, ulong dest_addr)
 	load_sernum_ethaddr ();
 #endif
 
-#if defined(CFG_GT_6426x) || defined(CONFIG_PN62) || defined(CONFIG_PPCHAMELEONEVB) || \
-    defined(CONFIG_MPC8540ADS) || defined(CONFIG_MPC8555CDS) || \
-    defined(CONFIG_MPC8560ADS) || defined(CONFIG_440_GX)
+#if defined(CONFIG_ETH1ADDR)
 	/* handle the 2nd ethernet address */
 
 	s = getenv ("eth1addr");
@@ -792,9 +790,7 @@ void board_init_r (gd_t *id, ulong dest_addr)
 			s = (*e) ? e + 1 : e;
 	}
 #endif
-#if defined(CFG_GT_6426x) || defined(CONFIG_MPC8540ADS) || \
-    defined(CONFIG_MPC8555CDS) || defined(CONFIG_MPC8560ADS) || \
-    defined(CONFIG_440_GX)
+#if defined(CONFIG_ETH2ADDR)
 	/* handle the 3rd ethernet address */
 
 	s = getenv ("eth2addr");
@@ -810,7 +806,7 @@ void board_init_r (gd_t *id, ulong dest_addr)
 	}
 #endif
 
-#if defined(CONFIG_440_GX)
+#if defined(CONFIG_ETH3ADDR)
 	/* handle 4th ethernet address */
 	s = getenv("eth3addr");
 #if defined(CONFIG_XPEDITE1K)