123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263 |
- This file contains information for VSC9953, a Vitesse L2 Switch IP
- which is integrated in the T1040/T1020 Freescale SoCs.
- About Device:
- =============
- VSC9953 is an 8-port Gigabit Ethernet switch supports the following features:
- - 8192 MAC addresses
- - Static Address provisioning
- - Dynamic learning of MAC addresses and aging
- - 4096 VLANs
- - Independent and shared VLAN learning (IVL, SVL)
- - Policing with storm control and MC/BC protection
- - IPv4 and IPv6 multicast
- - Jumbo frames (9.6 KB)
- - Access Control List
- - VLAN editing, translation and remarking
- - RMON counters per port
- Switch interfaces:
- - 8 Gigabit switch ports (ports 0 to 7) are external and are connected to external PHYs
- - 2 switch ports (ports 8 and 9) of 2.5 G are connected (fixed links)
- to FMan ports (FM1@DTSEC1 and FM1@DTSEC2)
- Commands Overview:
- =============
- Commands supported
- - enable/disable a port or show its configuration (speed, duplexity, status, etc.)
- - port statistics
- - MAC learning
- - add/remove FDB entries
- - Port-based VLAN
- - Private/Shared VLAN learning
- - VLAN ingress filtering
- - Port LAG
- Commands syntax
- ethsw [port <port_no>] { enable | disable | show } - enable/disable a port; show a port's configuration
- ethsw [port <port_no>] statistics { [help] | [clear] } - show an l2 switch port's statistics
- ethsw [port <port_no>] learning { [help] | show | auto | disable } - enable/disable/show learning configuration on a port
- ethsw [port <port_no>] [vlan <vid>] fdb { [help] | show | flush | { add | del } <mac> } - add/delete a mac entry in FDB; use show to see FDB entries;
- if [vlan <vid>] is missing, VID 1 will be used
- ethsw [port <port_no>] pvid { [help] | show | <pvid> } - set/show PVID (ingress and egress VLAN tagging) for a port
- ethsw [port <port_no>] vlan { [help] | show | add <vid> | del <vid> } - add a VLAN to a port (VLAN members)
- ethsw [port <port_no>] untagged { [help] | show | all | none | pvid } - set egress tagging mode for a port
- ethsw [port <port_no>] egress tag { [help] | show | pvid | classified } - configure VID source for egress tag.
- Tag's VID could be the frame's classified VID or the PVID of the port
- ethsw vlan fdb { [help] | show | shared | private } - make VLAN learning shared or private
- ethsw [port <port_no>] ingress filtering { [help] | show | enable | disable } - enable/disable VLAN ingress filtering on port
- ethsw [port <port_no>] aggr { [help] | show | <lag_group_no> } - get/set LAG group for a port
- => ethsw show
- Port Status Link Speed Duplex
- 0 enabled down 10 half
- 1 enabled down 10 half
- 2 enabled down 10 half
- 3 enabled up 1000 full
- 4 disabled down - half
- 5 disabled down - half
- 6 disabled down - half
- 7 disabled down - half
- 8 enabled up 2500 full
- 9 enabled up 2500 full
- =>
|