Kun Qin 5000d967d1 RaspberryPi: Platform Build: Resolving newly introduced dependency 1 year ago
..
RPi3.dsc 5000d967d1 RaspberryPi: Platform Build: Resolving newly introduced dependency 1 year ago
RPi3.fdf 69cefd028e Platform/RaspberryPi: Switch RPi3 USB NIC driver to Ax88772c 3 years ago
Readme.md 38c387d2da Platforms/RaspberryPi: Fix incorrect display resolution 3 years ago
Systems.md 86ef5b3e5d Platform/RPi3: Add Debian 10 installation in Systems.md 4 years ago

Readme.md

Raspberry Pi 3 Platform

Summary

This is a port of 64-bit Tiano Core UEFI firmware for the Raspberry Pi 3B (and related) platforms, based on Ard Biesheuvel’s 64-bit and Microsoft’s 32-bit implementations, as maintained by Andrei Warkentin.

This is meant as a generally useful 64-bit ATF + UEFI implementation for Raspberry Pi variants based on the BCM2837 SoC, which should be good enough for most kind of UEFI development, as well as for running consummer Operating Systems in such as Linux, Windows or the BSDs.

Raspberry Pi is a trademark of the Raspberry Pi Foundation.

Hardware Supported

The RPi3 target supports Pi revisions based on the BCM2837 SoC:

  • Raspberry Pi 2B v1.2 (older versions are not compatible)
  • Raspberry Pi 3A+
  • Raspberry Pi 3B
  • Raspberry Pi 3B+
  • Raspberry Pi CM3

Note: a CM3L, lacking eMMC and thus similar to the 3B, will probably work as well, but just has not been tested.

Please see the RPi4 target for BCM2711-based variants, such as the Raspberry Pi 4B.

Status

This firmware, that has been validated to compile against the current edk2/edk2-platforms, should be able to boot Linux (Debian, Ubuntu, SUSE), NetBSD, FreeBSD as well as Windows 10 ARM64 (full GUI version).

It also provides support for ATF (Arm Trusted Platform).

HDMI and the mini-UART serial port can be used for output devices, with mirrored output. USB keyboards and the mini-UART serial port can be used as input.

The default for the firmware is to first attempt boot from SD then USB. The UEFI Shell can also be accessed by pressing F1. To change the boot order you can edit the preferences in the Boot Maintenance Manager menu.

For additional information about the tested systems and how to set them up, please see Systems.md.

Building

Build instructions from the top level edk2-platforms Readme.md apply.

Booting the firmware

  1. Format a uSD card as FAT32
  2. Copy the generated RPI_EFI.fd firmware onto the partition
  3. Download and copy the following files from https://github.com/raspberrypi/firmware/tree/master/boot
    • bcm2710-rpi-3-b.dtb (for Pi 3B)
    • bcm2710-rpi-3-b-plus.dtb (for Pi 3B+)
    • bcm2710-rpi-2-b.dtb (for Pi 2B v1.2)
    • bcm2710-rpi-cm3.dtb (for Pi CM3)
    • bootcode.bin
    • fixup.dat
    • start.elf
    • overlays/miniuart-bt.dtbo or overlays/disable-bt.dtbo (Optional)
  4. Create a config.txt with the following content:

    arm_control=0x200
    enable_uart=1
    armstub=RPI_EFI.fd
    disable_commandline_tags=2
    device_tree_address=0x1f0000
    device_tree_end=0x200000
    

    If you want to use PL011 instead of the miniUART on your Pi 3B/3B+, you can add the lines:

    dtoverlay=miniuart-bt
    

    Note: doing so requires miniuart-bt.dbto to have been copied into an overlays/ directory on the uSD card. Alternatively, you may use disable-bt instead of miniuart-bt if you don’t require Bluetooth.

  5. Insert the uSD card and power up the Pi.

Note that if you have a model 3+ or a model 3 where you enabled USB boot through OTP (see here) you may also be able to boot from a FAT32 USB driver rather than uSD.

Notes

ARM Trusted Firmware (TF-A)

The TF-A binary files were compiled from the latest TF-A release. No aleration to the official source has been applied.

For more details on the TF-A compilation, see the relevant Readme in the TrustedFirmware/ directory from edk2-non-osi.

Custom Device Tree

By default, UEFI will use the device tree loaded by the VideoCore firmware. This depends on the model/variant, and relies on the presence on specific files on your boot media. E.g.:

  • bcm2710-rpi-3-b.dtb (for Pi 3B)
  • bcm2710-rpi-3-b-plus.dtb (for Pi 3B+)
  • bcm2710-rpi-2-b.dtb (for Pi 2B v1.2)
  • bcm2710-rpi-cm3.dtb (for Pi CM3)

You can override the DTB and provide a custom one. Copy the relevant .dtb into the root of the SD or USB, and then edit your config.txt so that it looks like:

(...)
disable_commandline_tags=2
device_tree_address=0x1f0000
device_tree_end=0x200000
device_tree=your_fdt_file.dtb

Note: the address range must be [0x1f0000:0x200000]. dtoverlay and dtparam parameters are also supported.

Custom bootargs

This firmware will honor the command line passed by the GPU via cmdline.txt.

Note, that the ultimate contents of /chosen/bootargs are a combination of several pieces:

  • GPU-passed hardware configuration.
  • Additional boot options passed via cmdline.txt.

Limitations

HDMI

The UEFI HDMI video support relies on the VC (that’s the GPU) firmware to correctly detect and configure the attached screen. Some screens are slow, and this detection may not occur fast enough. Finally, you may wish to be able to boot your Pi headless, yet be able to attach a display to it later for debugging.

To accommodate these issues, the following extra lines are recommended for your config.txt:

  • hdmi_force_hotplug=1 to allow plugging in video after system is booted.
  • hdmi_group=1 and hdmi_mode=4 to force a specific mode, both to accommodate late-plugged screens or buggy/slow screens. See official documentation to make sense of these parameters (example above sets up 720p 60Hz).

NVRAM

The Raspberry Pi has no NVRAM.

NVRAM is emulated, with the non-volatile store backed by the UEFI image itself. This means that any changes made in UEFI proper are persisted, but changes made from a High Level Operating System (HLOS) aren’t.

RTC

The Rasberry Pi has no RTC.

An RtcEpochSeconds NVRAM variable is used to store the boot time. This should allow you to set whatever date/time you want using the Shell date and time commands. While in UEFI or HLOS, the time will tick forward. RtcEpochSeconds is not updated on reboots.

uSD (and eMMC for CM3)

UEFI supports both the Arasan SDHCI and the Broadcom SDHost controllers to access the flash media (eMMC on CM3, and uSD slot on everything else). You can use either. The other controller gets routed to the SDIO WiFi card (N/A to models without WiFi). The choice made will impact ACPI OSes booted (e.g. Windows 10). Arasan, being an SDIO controller, is usually used with the WiFi adapter (where available). SDHost cannot be used with SDIO. In UEFI setup screen:

  • go to Device Manager
  • go to Raspberry Pi Configuration
  • go to SD/MMC Configuration
  • configure uSD/eMMC Routing

Known issues:

  • Arasan HS/4bit support is missing.
  • No 8 bit mode support for (e)MMC (slow UEFI file I/O on CM3).
  • Hacky (e)MMC support (no HS).
  • No card removal/replacement detection, tons of timeouts and slow down during boot without an uSD card present.

USB

  • USB1 BBB mass storage devices untested (USB2 and USB3 devices are fine).
  • Some USB1 CBI (e.g. UFI floppy) mass storage devices may not work.

ACPI

Both Arasan and SDHost SD controllers are exposed.

Note that the ACPI tables were derived or copied from the MS-IoT one. This means that they are not truly ACPI compliant, especially when it comes to their descriptors, and therefore not suitable for Linux environments. If you want to use a Linux HLOS, you are encouraged to install a kernel that relies on Device Tree rather than ACPI.

Missing Functionality

  • Network booting via onboard NIC.
  • SPCR hardcodes UART type to miniUART, and thus will not expose correct (PL011) UART on CM3 and Pi2B or if DT overlays to switch UART are used on Pi 3B/3B+/3A+.

Configuration Settings

The Raspberry Pi UEFI configuration settings can be viewed and changed using both the UI configuration menu (under Device Manager -> Raspberry Pi Configuration), as well as the UEFI Shell. To configure using the UEFI Shell, use setvar command to read/write the UEFI variables with GUID = CD7CC258-31DB-22E6-9F22-63B0B8EED6B5.

The syntax to read a setting is:

setvar <NAME> -guid CD7CC258-31DB-22E6-9F22-63B0B8EED6B5

The syntax to write a setting is:

setvar <NAME> -guid CD7CC258-31DB-22E6-9F22-63B0B8EED6B5 -bs -rt -nv =<VALUE>

For string-type settings (e.g. Asset Tag), the syntax to write is:

setvar <NAME> -guid CD7CC258-31DB-22E6-9F22-63B0B8EED6B5 -bs -rt -nv =L"<VALUE>" =0x0000
UEFI Setting NAME VALUE
CPU Configuration
CPU Clock CpuClock Low = 0x00000000
Default = 0x00000001 (default)
Max = 0x00000002
Custom = 0x00000003
CPU Clock Rate (MHz) CustomCpuClock Hex numeric value, 4-bytes
(e.g. 0x000005DC for 1500 MHz)
Display Configuration
Virtual 640x480 DisplayEnableScaledVModes Checked = Bit 1 set (i.e. <DisplayEnableScaledVModes> \| 0x02)
Virtual 800x600 DisplayEnableScaledVModes Checked = Bit 0 set (i.e. <DisplayEnableScaledVModes> \| 0x01)
Virtual 1024x768 DisplayEnableScaledVModes Checked = Bit 2 set (i.e. <DisplayEnableScaledVModes> \| 0x04)
Virtual 720p DisplayEnableScaledVModes Checked = Bit 3 set (i.e. <DisplayEnableScaledVModes> \| 0x08)
Virtual 1080p DisplayEnableScaledVModes Checked = Bit 4 set (i.e. <DisplayEnableScaledVModes> \| 0x10)
Native resolution DisplayEnableScaledVModes Checked = Bit 5 set (i.e. <DisplayEnableScaledVModes> \| 0x20) (default)
Screenshot support DisplayEnableSShot Control-Alt-F12 = 0x00000001 (default)
Not Enabled = 0x00000000
Advanced Configuration
System Table Selection SystemTableMode ACPI = 0x00000000
ACPI + Devicetree = 0x00000001 (default)
Devicetree = 0x00000002
Asset Tag AssetTag String, 32 characters or less (e.g. L"ABCD123")
(default L"")
SD/MMC Configuration
uSD/eMMC Routing SdIsArasan Arasan SDHC = 0x00000001
Broadcom SDHOST = 0x00000000 (default)
Multi-Block Support MmcDisableMulti Multi-block transfers = 0x00000000 (default)
Single block transfers = 0x00000001
uSD Max Bus Width MmcForce1Bit 4-bit Mode = 0x00000000 (default)
1-bit Mode = 0x00000001
uSD Force Default Speed MmcForceDefaultSpeed Allow High Speed = 0x00000000 (default)
Force Default Speed = 0x00000001
SD Default Speed (MHz) MmcSdDefaultSpeedMHz Hex numeric value, 4-bytes (e.g. 0x00000019 for 25 MHz)
(default 25)
SD High Speed (MHz) MmcSdHighSpeedMHz Hex numeric value, 4-bytes (e.g. 0x00000032 for 50 MHz)
(default 50)
Debugging Configuration
JTAG Routing DebugEnableJTAG Enable JTAG via GPIO = 0x00000001
Disable JTAG= 0x00000000 (default)

Examples:

  • To read the ‘System Table Selection’ setting :

    setvar SystemTableMode -guid CD7CC258-31DB-22E6-9F22-63B0B8EED6B5
    
  • To change the ‘System Table Selection’ setting to ‘Devicetree’ :

    setvar SystemTableMode -guid CD7CC258-31DB-22E6-9F22-63B0B8EED6B5 -bs -rt -nv =0x00000002
    
  • To change the Asset Tag to the string «ASSET-TAG-123» :

    setvar AssetTag -guid CD7CC258-31DB-22E6-9F22-63B0B8EED6B5 -bs -rt -nv =L"ASSET-TAG-123" =0x0000