gpio.md 4.5 KB

GPIO Module

Since Origin / Contributor Maintainer Source
2014-12-22 Zeroday Zeroday gpio.c

This module provides access to the GPIO (General Purpose Input/Output) subsystem.

All access is based on the I/O index number on the NodeMCU dev kits, not the internal GPIO pin. For example, the D0 pin on the dev kit is mapped to the internal GPIO pin 16.

If not using a NodeMCU dev kit, please refer to the below GPIO pin maps for the index↔gpio mapping.

IO index ESP8266 pin IO index ESP8266 pin
0 [*] GPIO16 7 GPIO13
1 GPIO5 8 GPIO15
2 GPIO4 9 GPIO3
3 GPIO0 10 GPIO1
4 GPIO2 11 GPIO9
5 GPIO14 12 GPIO10
6 GPIO12

** [*] D0(GPIO16) can only be used as gpio read/write. No interrupt support. No pwm/i2c/ow support. **

gpio.mode()

Initialize pin to GPIO mode, set the pin in/out direction, and optional internal pullup.

Syntax

gpio.mode(pin, mode [, pullup])

Parameters

  • pin pin to configure, IO index
  • mode one of gpio.OUTPUT or gpio.INPUT, or gpio.INT(interrupt mode)
  • pullup gpio.PULLUP or gpio.FLOAT; default is gpio.FLOAT

Returns

nil

Example

gpio.mode(0, gpio.OUTPUT)

See also

gpio.read()

Read digital GPIO pin value.

Syntax

gpio.read(pin)

Parameters

pin pin to read, IO index

Returns

a number, 0 = low, 1 = high

Example

-- read value of gpio 0.
gpio.read(0)

See also

gpio.mode()

gpio.serout()

Serialize output based on a sequence of delay-times. After each delay, the pin is toggled.

Syntax

gpio.serout(pin, start_level, delay_times [, repeat_num])

Parameters

  • pin pin to use, IO index
  • start_level level to start on, either gpio.HIGH or gpio.LOW
  • delay_times an array of delay times between each toggle of the gpio pin.
  • repeat_num an optional number of times to run through the sequence.

Note that this function blocks, and as such any use of it must adhere to the SDK guidelines of time spent blocking the stack (10-100ms). Failure to do so may lead to WiFi issues or outright crashes/reboots.

Returns

nil

Example

gpio.mode(1,gpio.OUTPUT,gpio.PULLUP)
gpio.serout(1,1,{30,30,60,60,30,30})  -- serial one byte, b10110010
gpio.serout(1,1,{30,70},8)  -- serial 30% pwm 10k, lasts 8 cycles
gpio.serout(1,1,{3,7},8)  -- serial 30% pwm 100k, lasts 8 cycles
gpio.serout(1,1,{0,0},8)  -- serial 50% pwm as fast as possible, lasts 8 cycles
gpio.serout(1,0,{20,10,10,20,10,10,10,100}) -- sim uart one byte 0x5A at about 100kbps
gpio.serout(1,1,{8,18},8) -- serial 30% pwm 38k, lasts 8 cycles

gpio.trig()

Establish a callback function to run on interrupt for a pin.

There is currently no support for unregistering the callback.

This function is not available if GPIO_INTERRUPT_ENABLE was undefined at compile time.

Syntax

gpio.trig(pin, type [, function(level)])

Parameters

  • pin 1~12, IO index, pin D0 does not support interrupt.
  • type «up», «down», «both», «low», «high», which represent rising edge, falling edge, both edge, low level, high level trig mode correspondingly.
  • function(level) callback function when triggered. The gpio level is the param. Use previous callback function if undefined here.

Returns

nil

Example

-- use pin 1 as the input pulse width counter
pin = 1
pulse1 = 0
du = 0
gpio.mode(pin,gpio.INT)
function pin1cb(level)
  du = tmr.now() - pulse1
  print(du)
  pulse1 = tmr.now()
  if level == gpio.HIGH then gpio.trig(pin, "down") else gpio.trig(pin, "up") end
end
gpio.trig(pin, "down", pin1cb)

See also

gpio.mode()

gpio.write()

Set digital GPIO pin value.

Syntax

gpio.write(pin, level)

Parameters

  • pin pin to write, IO index
  • level gpio.HIGH or gpio.LOW

Returns

nil

Example

-- set pin index 1 to GPIO mode, and set the pin to high.
pin=1
gpio.mode(pin, gpio.OUTPUT)
gpio.write(pin, gpio.HIGH)

See also