# NXP LPC1754 Cortex-M3 with 128kB Flash and 16kB+16kB Local On-Chip SRAM, # reset_config trst_and_srst if { [info exists CHIPNAME] } { set _CHIPNAME $CHIPNAME } else { set _CHIPNAME lpc1754 } # After reset the chip is clocked by the ~4MHz internal RC oscillator. # When board-specific code (reset-init handler or device firmware) # configures another oscillator and/or PLL0, set CCLK to match; if # you don't, then flash erase and write operations may misbehave. # (The ROM code doing those updates cares about core clock speed...) # # CCLK is the core clock frequency in KHz if { [info exists CCLK ] } { set _CCLK $CCLK } else { set _CCLK 4000 } if { [info exists CPUTAPID ] } { set _CPUTAPID $CPUTAPID } else { set _CPUTAPID 0x4ba00477 } #delays on reset lines #if your OpenOCD version rejects "jtag_nsrst_delay" replace it with: adapter_nsrst_delay 200 #jtag_nsrst_delay 200 #jtag_ntrst_delay 200 # LPC2000 & LPC1700 -> SRST causes TRST #reset_config srst_pulls_trst reset_config trst_and_srst srst_push_pull trst_push_pull jtag newtap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID #jtag newtap x3s tap -irlen 6 -ircapture 0x11 -irmask 0x11 -expected-id 0x0141c093 set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME cortex_m3 -chain-position $_TARGETNAME -event reset-init 0 # LPC1754 has 16kB of SRAM In the ARMv7-M "Code" area (at 0x10000000) # and 16K more on AHB, in the ARMv7-M "SRAM" area, (at 0x2007c000). $_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size 0x4000 $_TARGETNAME configure -work-area-phys 0x2007c000 -work-area-size 0x4000 # LPC1754 has 128kB of flash memory, managed by ROM code (including a # boot loader which verifies the flash exception table's checksum). # flash bank lpc2000 0 0 [calc checksum] set _FLASHNAME $_CHIPNAME.flash flash bank $_FLASHNAME lpc2000 0x0 0x20000 0 0 $_TARGETNAME \ lpc1700 $_CCLK calc_checksum # Run with *real slow* clock by default since the # boot rom could have been playing with the PLL, so # we have no idea what clock the target is running at. adapter_khz 1000 $_TARGETNAME configure -event reset-init { # Do not remap 0x0000-0x0020 to anything but the flash (i.e. select # "User Flash Mode" where interrupt vectors are _not_ remapped, # and reside in flash instead). # # See Table 612. Memory Mapping Control register (MEMMAP - 0x400F C040) bit description # Bit Symbol Value Description Reset # value # 0 MAP Memory map control. 0 # 0 Boot mode. A portion of the Boot ROM is mapped to address 0. # 1 User mode. The on-chip Flash memory is mapped to address 0. # 31:1 - Reserved. The value read from a reserved bit is not defined. NA # # http://ics.nxp.com/support/documents/microcontrollers/?scope=LPC1768&type=user mww 0x400FC040 0x01 }