apalix-imx8.rst 2.2 KB

12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576777879808182
  1. .. SPDX-License-Identifier: GPL-2.0+
  2. Apalis iMX8QM V1.0B Module
  3. ==========================
  4. Quick Start
  5. -----------
  6. - Build the ARM trusted firmware binary
  7. - Get scfw_tcm.bin and ahab-container.img
  8. - Build U-Boot
  9. - Load U-Boot binary using uuu
  10. - Flash U-Boot binary into the eMMC
  11. - Boot
  12. Get and Build the ARM Trusted Firmware
  13. --------------------------------------
  14. .. code-block:: bash
  15. $ git clone -b imx_4.14.78_1.0.0_ga https://source.codeaurora.org/external/imx/imx-atf
  16. $ cd imx-atf/
  17. $ make PLAT=imx8qm bl31
  18. Get scfw_tcm.bin and ahab-container.img
  19. ---------------------------------------
  20. .. code-block:: bash
  21. $ wget https://github.com/toradex/meta-fsl-bsp-release/blob/toradex-sumo-4.14.78-1.0.0_ga-bringup/imx/meta-bsp/recipes-
  22. bsp/imx-sc-firmware/files/mx8qm-apalis-scfw-tcm.bin?raw=true
  23. $ mv mx8qm-apalis-scfw-tcm.bin\?raw\=true mx8qm-apalis-scfw-tcm.bin
  24. $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin
  25. $ chmod +x firmware-imx-8.0.bin
  26. $ ./firmware-imx-8.0.bin
  27. Copy the following binaries to the U-Boot folder:
  28. .. code-block:: bash
  29. $ cp imx-atf/build/imx8qm/release/bl31.bin .
  30. $ cp u-boot/u-boot.bin .
  31. Copy the following firmware to the U-Boot folder:
  32. .. code-block:: bash
  33. $ cp firmware-imx-8.0/firmware/seco/ahab-container.img .
  34. Build U-Boot
  35. ------------
  36. .. code-block:: bash
  37. $ make apalis-imx8_defconfig
  38. $ make u-boot-dtb.imx
  39. Load the U-Boot Binary Using UUU
  40. --------------------------------
  41. Get the latest version of the universal update utility (uuu) aka ``mfgtools 3.0``:
  42. https://community.nxp.com/external-link.jspa?url=https%3A%2F%2Fgithub.com%2FNXPmicro%2Fmfgtools%2Freleases
  43. Put the module into USB recovery aka serial downloader mode, connect USB device
  44. to your host and execute uuu:
  45. .. code-block:: bash
  46. sudo ./uuu u-boot/u-boot-dtb.imx
  47. Flash the U-Boot Binary into the eMMC
  48. -------------------------------------
  49. Burn the ``u-boot-dtb.imx`` binary to the primary eMMC hardware boot area
  50. partition and boot:
  51. .. code-block:: bash
  52. load mmc 1:1 $loadaddr u-boot-dtb.imx
  53. setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt ${blkcnt} / 0x200
  54. mmc dev 0 1
  55. mmc write ${loadaddr} 0x0 ${blkcnt}