123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177 |
- if ARCH_ZYNQMP
- config SPL_FS_FAT
- default y
- config SPL_LIBCOMMON_SUPPORT
- default y
- config SPL_LIBDISK_SUPPORT
- default y
- config SPL_LIBGENERIC_SUPPORT
- default y
- config SPL_MMC_SUPPORT
- default y if MMC_SDHCI_ZYNQ
- config SPL_SERIAL_SUPPORT
- default y
- config SPL_SPI_FLASH_SUPPORT
- default y if ZYNQ_QSPI
- config SPL_SPI_SUPPORT
- default y if ZYNQ_QSPI
- config SYS_BOARD
- default "zynqmp"
- config SYS_VENDOR
- string "Vendor name"
- default "xilinx"
- config SYS_SOC
- default "zynqmp"
- config SYS_CONFIG_NAME
- string "Board configuration name"
- default "xilinx_zynqmp"
- help
- This option contains information about board configuration name.
- Based on this option include/configs/<CONFIG_SYS_CONFIG_NAME>.h header
- will be used for board configuration.
- config SYS_MEM_RSVD_FOR_MMU
- bool "Reserve memory for MMU Table"
- help
- If defined this option is used to setup different space for
- MMU table than the one which will be allocated during
- relocation.
- config BOOT_INIT_FILE
- string "boot.bin init register filename"
- depends on SPL
- default ""
- help
- Add register writes to boot.bin format (max 256 pairs).
- Expect a table of register-value pairs, e.g. "0x12345678 0x4321"
- config PMUFW_INIT_FILE
- string "PMU firmware"
- depends on SPL
- default ""
- help
- Include external PMUFW (Platform Management Unit FirmWare) to
- a Xilinx bootable image (boot.bin).
- config ZYNQMP_SPL_PM_CFG_OBJ_FILE
- string "PMU firmware configuration object to load at runtime by SPL"
- depends on SPL
- help
- Path to a binary PMU firmware configuration object to be linked
- into U-Boot SPL and loaded at runtime into the PMU firmware.
- The ZynqMP Power Management Unit (PMU) needs a configuration
- object for most SoC peripherals to work. To have it loaded by
- U-Boot SPL set here the file name (absolute path or relative to
- the top source tree) of your configuration, which must be a
- binary blob. It will be linked in the SPL binary and loaded
- into the PMU firmware by U-Boot SPL during board
- initialization.
- Leave this option empty if your PMU firmware has a hard-coded
- configuration object or you are loading it by any other means.
- config ZYNQMP_USB
- bool "Configure ZynqMP USB"
- config ZYNQMP_NO_DDR
- bool "Disable DDR MMU mapping"
- help
- This option configures MMU with no DDR to avoid speculative
- access to DDR memory where DDR is not present.
- config SYS_MALLOC_F_LEN
- default 0x600
- config DEFINE_TCM_OCM_MMAP
- bool "Define TCM and OCM memory in MMU Table"
- default y if MP
- help
- This option if enabled defines the TCM and OCM memory and its
- memory attributes in MMU table entry.
- config ZYNQMP_PSU_INIT_ENABLED
- bool "Include psu_init"
- help
- Include psu_init to full u-boot. SPL include psu_init by default.
- config SPL_ZYNQMP_ALT_BOOTMODE_ENABLED
- bool "Overwrite SPL bootmode"
- depends on SPL
- help
- Overwrite bootmode selected via boot mode pins to tell SPL what should
- be the next boot device.
- config ZYNQ_SDHCI_MAX_FREQ
- default 200000000
- config SPL_ZYNQMP_ALT_BOOTMODE
- hex
- default 0x0 if JTAG_MODE
- default 0x1 if QSPI_MODE_24BIT
- default 0x2 if QSPI_MODE_32BIT
- default 0x3 if SD_MODE
- default 0x4 if NAND_MODE
- default 0x5 if SD_MODE1
- default 0x6 if EMMC_MODE
- default 0x7 if USB_MODE
- default 0xa if SW_USBHOST_MODE
- default 0xb if SW_SATA_MODE
- default 0xe if SD1_LSHFT_MODE
- choice
- prompt "Boot mode"
- depends on SPL_ZYNQMP_ALT_BOOTMODE_ENABLED
- default JTAG_MODE
- config JTAG_MODE
- bool "JTAG_MODE"
- config QSPI_MODE_24BIT
- bool "QSPI_MODE_24BIT"
- config QSPI_MODE_32BIT
- bool "QSPI_MODE_32BIT"
- config SD_MODE
- bool "SD_MODE"
- config SD_MODE1
- bool "SD_MODE1"
- config NAND_MODE
- bool "NAND_MODE"
- config EMMC_MODE
- bool "EMMC_MODE"
- config USB_MODE
- bool "USB"
- config SW_USBHOST_MODE
- bool "SW USBHOST_MODE"
- config SW_SATA_MODE
- bool "SW SATA_MODE"
- config SD1_LSHFT_MODE
- bool "SD1_LSHFT_MODE"
- endchoice
- source "board/xilinx/Kconfig"
- source "board/xilinx/zynqmp/Kconfig"
- endif
|