123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113 |
- /* SPDX-License-Identifier: GPL-2.0+ */
- /*
- * (C) Copyright 2011
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Lei Wen <leiwen@marvell.com>
- */
- /*
- * This file should be included in board config header file.
- *
- * It supports common definitions for Kirkwood platform
- */
- #ifndef _KW_CONFIG_H
- #define _KW_CONFIG_H
- #if defined (CONFIG_KW88F6281)
- #include <asm/arch/kw88f6281.h>
- #elif defined (CONFIG_KW88F6192)
- #include <asm/arch/kw88f6192.h>
- #else
- #error "SOC Name not defined"
- #endif /* CONFIG_KW88F6281 */
- #include <asm/arch/soc.h>
- #define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
- #define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
- #define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
- /*
- * By default kwbimage.cfg from board specific folder is used
- * If for some board, different configuration file need to be used,
- * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
- */
- #ifndef CONFIG_SYS_KWD_CONFIG
- #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
- #endif /* CONFIG_SYS_KWD_CONFIG */
- /* Kirkwood has 2k of Security SRAM, use it for SP */
- #define CONFIG_SYS_INIT_SP_ADDR 0xC8012000
- #define CONFIG_I2C_MVTWSI_BASE0 KW_TWSI_BASE
- #define MV_UART_CONSOLE_BASE KW_UART0_BASE
- #define MV_SATA_BASE KW_SATA_BASE
- #define MV_SATA_PORT0_OFFSET KW_SATA_PORT0_OFFSET
- #define MV_SATA_PORT1_OFFSET KW_SATA_PORT1_OFFSET
- /*
- * NAND configuration
- */
- #ifdef CONFIG_CMD_NAND
- #define CONFIG_NAND_KIRKWOOD
- #define CONFIG_SYS_NAND_BASE 0xD8000000 /* MV_DEFADR_NANDF */
- #define NAND_ALLOW_ERASE_ALL 1
- #endif
- /*
- * Ethernet Driver configuration
- */
- #ifdef CONFIG_CMD_NET
- #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
- #define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
- #endif /* CONFIG_CMD_NET */
- /*
- * USB/EHCI
- */
- #ifdef CONFIG_CMD_USB
- #define CONFIG_EHCI_IS_TDI
- #endif /* CONFIG_CMD_USB */
- /*
- * IDE Support on SATA ports
- */
- #ifdef CONFIG_IDE
- #define __io
- #define CONFIG_IDE_PREINIT
- #define CONFIG_MVSATA_IDE_USE_PORT1
- /* Needs byte-swapping for ATA data register */
- #define CONFIG_IDE_SWAP_IO
- /* Data, registers and alternate blocks are at the same offset */
- #define CONFIG_SYS_ATA_DATA_OFFSET (0x0100)
- #define CONFIG_SYS_ATA_REG_OFFSET (0x0100)
- #define CONFIG_SYS_ATA_ALT_OFFSET (0x0100)
- /* Each 8-bit ATA register is aligned to a 4-bytes address */
- #define CONFIG_SYS_ATA_STRIDE 4
- /* Controller supports 48-bits LBA addressing */
- #define CONFIG_LBA48
- /* CONFIG_IDE requires some #defines for ATA registers */
- #define CONFIG_SYS_IDE_MAXBUS 2
- #define CONFIG_SYS_IDE_MAXDEVICE 2
- /* ATA registers base is at SATA controller base */
- #define CONFIG_SYS_ATA_BASE_ADDR MV_SATA_BASE
- #endif /* CONFIG_IDE */
- /*
- * I2C related stuff
- */
- #if defined(CONFIG_CMD_I2C) && !defined(CONFIG_DM_I2C)
- #ifndef CONFIG_SYS_I2C_SOFT
- #define CONFIG_SYS_I2C
- #define CONFIG_SYS_I2C_MVTWSI
- #endif
- #define CONFIG_SYS_I2C_SLAVE 0x0
- #define CONFIG_SYS_I2C_SPEED 100000
- #endif
- /* Use common timer */
- #define CONFIG_SYS_TIMER_COUNTS_DOWN
- #define CONFIG_SYS_TIMER_COUNTER (MVEBU_TIMER_BASE + 0x14)
- #define CONFIG_SYS_TIMER_RATE CONFIG_SYS_TCLK
- #endif /* _KW_CONFIG_H */
|