SBx81LIFXCAT.h 2.9 KB

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495
  1. /* SPDX-License-Identifier: GPL-2.0+ */
  2. /*
  3. * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz>
  4. */
  5. #ifndef _CONFIG_SBX81LIFXCAT_H
  6. #define _CONFIG_SBX81LIFXCAT_H
  7. /*
  8. * High Level Configuration Options (easy to change)
  9. */
  10. #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
  11. #define CONFIG_KW88F6281 1 /* SOC Name */
  12. #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
  13. #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
  14. /* additions for new ARM relocation support */
  15. #define CONFIG_SYS_SDRAM_BASE 0x00000000
  16. #define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
  17. #define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
  18. #define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */
  19. #define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
  20. #define CONFIG_KIRKWOOD_GPIO 1
  21. /*
  22. * NS16550 Configuration
  23. */
  24. #define CONFIG_SYS_NS16550
  25. #define CONFIG_SYS_NS16550_SERIAL
  26. #define CONFIG_SYS_NS16550_REG_SIZE (-4)
  27. #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
  28. #define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
  29. /*
  30. * Serial Port configuration
  31. * The following definitions let you select what serial you want to use
  32. * for your console driver.
  33. */
  34. /*
  35. * For booting Linux, the board info and command line data
  36. * have to be in the first 8 MB of memory, since this is
  37. * the maximum mapped by the Linux kernel during initialization.
  38. */
  39. #define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
  40. #define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
  41. #define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
  42. #define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
  43. #define MTDPARTS_MTDOOPS "errlog"
  44. #define CONFIG_DOS_PARTITION
  45. /*
  46. * Environment variables configurations
  47. */
  48. /*
  49. * U-Boot bootcode configuration
  50. */
  51. #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */
  52. #define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */
  53. /*
  54. * For booting Linux, the board info and command line data
  55. * have to be in the first 8 MB of memory, since this is
  56. * the maximum mapped by the Linux kernel during initialization.
  57. */
  58. #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
  59. /* size in bytes reserved for initial data */
  60. #include <asm/arch/config.h>
  61. /* There is no PHY directly connected so don't ask it for link status */
  62. #undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  63. /*
  64. * Other required minimal configurations
  65. */
  66. #define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
  67. /*
  68. * Ethernet Driver configuration
  69. */
  70. #ifdef CONFIG_CMD_NET
  71. #define CONFIG_NET_MULTI /* specify more that one ports available */
  72. #define CONFIG_MVGBE /* Enable kirkwood Gbe Controller Driver */
  73. #define CONFIG_MVGBE_PORTS {1, 0} /* enable a single port */
  74. #define CONFIG_PHY_BASE_ADR 0x01
  75. #endif /* CONFIG_CMD_NET */
  76. #define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */
  77. #endif /* _CONFIG_SBX81LIFXCAT_H */