123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159 |
- .. SPDX-License-Identifier: GPL-2.0+
- U-Boot for Khadas VIM3
- ======================
- Khadas VIM3 is a single board computer manufactured by Shenzhen Wesion
- Technology Co., Ltd. with the following specifications:
- - Amlogic A311D Arm Cortex-A53 dual-core + Cortex-A73 quad-core SoC
- - 4GB LPDDR4 SDRAM
- - Gigabit Ethernet
- - HDMI 2.1 display
- - 40-pin GPIO header
- - 1 x USB 3.0 Host, 1 x USB 2.0 Host
- - eMMC, microSD
- - M.2
- - Infrared receiver
- Schematics are available on the manufacturer website.
- PCIe Setup
- ----------
- The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
- lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
- an USB3.0 Type A connector and a M.2 Key M slot.
- The PHY driving these differential lines is shared between
- the USB3.0 controller and the PCIe Controller, thus only
- a single controller can use it.
- To setup for PCIe, run the following commands from U-Boot:
- .. code-block:: none
- i2c dev i2c@5000
- i2c mw 0x18 0x33 1
- Then power-cycle the board.
- To set back to USB3.0, run the following commands from U-Boot:
- .. code-block:: none
- i2c dev i2c@5000
- i2c mw 0x18 0x33 0
- Then power-cycle the board.
- U-Boot compilation
- ------------------
- .. code-block:: bash
- $ export CROSS_COMPILE=aarch64-none-elf-
- $ make khadas-vim3_defconfig
- $ make
- Image creation
- --------------
- Amlogic doesn't provide sources for the firmware and for tools needed
- to create the bootloader image, so it is necessary to obtain them from
- the git tree published by the board vendor:
- .. code-block:: bash
- $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
- $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
- $ tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
- $ tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
- $ export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
- $ DIR=vim3-u-boot
- $ git clone --depth 1 \
- https://github.com/khadas/u-boot.git -b khadas-vims-v2015.01 \
- $DIR
- $ cd vim3-u-boot
- $ make kvim3_defconfig
- $ make
- $ export UBOOTDIR=$PWD
- Go back to mainline U-Boot source tree then :
- .. code-block:: bash
- $ mkdir fip
- $ cp $UBOOTDIR/build/scp_task/bl301.bin fip/
- $ cp $UBOOTDIR/build/board/khadas/kvim3/firmware/acs.bin fip/
- $ cp $UBOOTDIR/fip/g12b/bl2.bin fip/
- $ cp $UBOOTDIR/fip/g12b/bl30.bin fip/
- $ cp $UBOOTDIR/fip/g12b/bl31.img fip/
- $ cp $UBOOTDIR/fip/g12b/ddr3_1d.fw fip/
- $ cp $UBOOTDIR/fip/g12b/ddr4_1d.fw fip/
- $ cp $UBOOTDIR/fip/g12b/ddr4_2d.fw fip/
- $ cp $UBOOTDIR/fip/g12b/diag_lpddr4.fw fip/
- $ cp $UBOOTDIR/fip/g12b/lpddr3_1d.fw fip/
- $ cp $UBOOTDIR/fip/g12b/lpddr4_1d.fw fip/
- $ cp $UBOOTDIR/fip/g12b/lpddr4_2d.fw fip/
- $ cp $UBOOTDIR/fip/g12b/piei.fw fip/
- $ cp $UBOOTDIR/fip/g12b/aml_ddr.fw fip/
- $ cp u-boot.bin fip/bl33.bin
- $ sh fip/blx_fix.sh \
- fip/bl30.bin \
- fip/zero_tmp \
- fip/bl30_zero.bin \
- fip/bl301.bin \
- fip/bl301_zero.bin \
- fip/bl30_new.bin \
- bl30
- $ sh fip/blx_fix.sh \
- fip/bl2.bin \
- fip/zero_tmp \
- fip/bl2_zero.bin \
- fip/acs.bin \
- fip/bl21_zero.bin \
- fip/bl2_new.bin \
- bl2
- $ $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl30sig --input fip/bl30_new.bin \
- --output fip/bl30_new.bin.g12a.enc \
- --level v3
- $ $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl3sig --input fip/bl30_new.bin.g12a.enc \
- --output fip/bl30_new.bin.enc \
- --level v3 --type bl30
- $ $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl3sig --input fip/bl31.img \
- --output fip/bl31.img.enc \
- --level v3 --type bl31
- $ $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl3sig --input fip/bl33.bin --compress lz4 \
- --output fip/bl33.bin.enc \
- --level v3 --type bl33 --compress lz4
- $ $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl2sig --input fip/bl2_new.bin \
- --output fip/bl2.n.bin.sig
- $ $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bootmk \
- --output fip/u-boot.bin \
- --bl2 fip/bl2.n.bin.sig \
- --bl30 fip/bl30_new.bin.enc \
- --bl31 fip/bl31.img.enc \
- --bl33 fip/bl33.bin.enc \
- --ddrfw1 fip/ddr4_1d.fw \
- --ddrfw2 fip/ddr4_2d.fw \
- --ddrfw3 fip/ddr3_1d.fw \
- --ddrfw4 fip/piei.fw \
- --ddrfw5 fip/lpddr4_1d.fw \
- --ddrfw6 fip/lpddr4_2d.fw \
- --ddrfw7 fip/diag_lpddr4.fw \
- --ddrfw8 fip/aml_ddr.fw \
- --ddrfw9 fip/lpddr3_1d.fw \
- --level v3
- and then write the image to SD with:
- .. code-block:: bash
- $ DEV=/dev/your_sd_device
- $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
- $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
|