sys_proto.h 3.7 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125
  1. /*
  2. * (C) Copyright 2010
  3. * Texas Instruments, <www.ti.com>
  4. *
  5. * This program is free software; you can redistribute it and/or
  6. * modify it under the terms of the GNU General Public License as
  7. * published by the Free Software Foundation; either version 2 of
  8. * the License, or (at your option) any later version.
  9. *
  10. * This program is distributed in the hope that it will be useful,
  11. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  12. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  13. * GNU General Public License for more details.
  14. *
  15. * You should have received a copy of the GNU General Public License
  16. * along with this program; if not, write to the Free Software
  17. * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  18. * MA 02111-1307 USA
  19. */
  20. #ifndef _SYS_PROTO_H_
  21. #define _SYS_PROTO_H_
  22. #include <asm/arch/omap.h>
  23. #include <asm/io.h>
  24. #include <asm/arch/clocks.h>
  25. #include <asm/omap_common.h>
  26. #include <asm/arch/clocks.h>
  27. struct pad_conf_entry {
  28. u32 offset;
  29. u32 val;
  30. };
  31. struct omap_sysinfo {
  32. char *board_string;
  33. };
  34. extern const struct omap_sysinfo sysinfo;
  35. void gpmc_init(void);
  36. void watchdog_init(void);
  37. u32 get_device_type(void);
  38. void do_set_mux(u32 base, struct pad_conf_entry const *array, int size);
  39. void set_muxconf_regs_essential(void);
  40. void set_muxconf_regs_non_essential(void);
  41. void sr32(void *, u32, u32, u32);
  42. u32 wait_on_value(u32, u32, void *, u32);
  43. void sdelay(unsigned long);
  44. void setup_clocks_for_console(void);
  45. void prcm_init(void);
  46. void bypass_dpll(u32 const base);
  47. void freq_update_core(void);
  48. u32 get_sys_clk_freq(void);
  49. u32 omap5_ddr_clk(void);
  50. void cancel_out(u32 *num, u32 *den, u32 den_limit);
  51. void sdram_init(void);
  52. u32 omap_sdram_size(void);
  53. u32 cortex_rev(void);
  54. void init_omap_revision(void);
  55. void do_io_settings(void);
  56. void omap_vc_init(u16 speed_khz);
  57. int omap_vc_bypass_send_value(u8 sa, u8 reg_addr, u8 reg_data);
  58. u32 warm_reset(void);
  59. void force_emif_self_refresh(void);
  60. void get_ioregs(const struct ctrl_ioregs **regs);
  61. void srcomp_enable(void);
  62. /*
  63. * This is used to verify if the configuration header
  64. * was executed by Romcode prior to control of transfer
  65. * to the bootloader. SPL is responsible for saving and
  66. * passing this to the u-boot.
  67. */
  68. extern struct omap_boot_parameters boot_params;
  69. static inline u32 running_from_sdram(void)
  70. {
  71. u32 pc;
  72. asm volatile ("mov %0, pc" : "=r" (pc));
  73. return ((pc >= OMAP54XX_DRAM_ADDR_SPACE_START) &&
  74. (pc < OMAP54XX_DRAM_ADDR_SPACE_END));
  75. }
  76. static inline u8 uboot_loaded_by_spl(void)
  77. {
  78. /*
  79. * u-boot can be running from sdram either because of configuration
  80. * Header or by SPL. If because of CH, then the romcode sets the
  81. * CHSETTINGS executed bit to true in the boot parameter structure that
  82. * it passes to the bootloader.This parameter is stored in the ch_flags
  83. * variable by both SPL and u-boot.Check out for CHSETTINGS, which is a
  84. * mandatory section if CH is present.
  85. */
  86. if ((boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS))
  87. return 0;
  88. else
  89. return running_from_sdram();
  90. }
  91. /*
  92. * The basic hardware init of OMAP(s_init()) can happen in 4
  93. * different contexts:
  94. * 1. SPL running from SRAM
  95. * 2. U-Boot running from FLASH
  96. * 3. Non-XIP U-Boot loaded to SDRAM by SPL
  97. * 4. Non-XIP U-Boot loaded to SDRAM by ROM code using the
  98. * Configuration Header feature
  99. *
  100. * This function finds this context.
  101. * Defining as inline may help in compiling out unused functions in SPL
  102. */
  103. static inline u32 omap_hw_init_context(void)
  104. {
  105. #ifdef CONFIG_SPL_BUILD
  106. return OMAP_INIT_CONTEXT_SPL;
  107. #else
  108. if (uboot_loaded_by_spl())
  109. return OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL;
  110. else if (running_from_sdram())
  111. return OMAP_INIT_CONTEXT_UBOOT_AFTER_CH;
  112. else
  113. return OMAP_INIT_CONTEXT_UBOOT_FROM_NOR;
  114. #endif
  115. }
  116. #endif