|
@@ -0,0 +1,248 @@
|
|
|
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
|
|
+/*
|
|
|
+ * Copyright (c) 2018 BayLibre, SAS.
|
|
|
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
|
|
|
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
|
|
|
+ */
|
|
|
+
|
|
|
+/dts-v1/;
|
|
|
+
|
|
|
+#include <dt-bindings/input/input.h>
|
|
|
+
|
|
|
+#include "meson-gxl-s905x.dtsi"
|
|
|
+
|
|
|
+/ {
|
|
|
+ compatible = "libretech,aml-s805x-ac", "amlogic,s805x",
|
|
|
+ "amlogic,meson-gxl";
|
|
|
+ model = "Libre Computer Board AML-S805X-AC";
|
|
|
+
|
|
|
+ aliases {
|
|
|
+ serial0 = &uart_AO;
|
|
|
+ ethernet0 = ðmac;
|
|
|
+ spi0 = &spifc;
|
|
|
+ };
|
|
|
+
|
|
|
+ chosen {
|
|
|
+ stdout-path = "serial0:115200n8";
|
|
|
+ };
|
|
|
+
|
|
|
+ cvbs-connector {
|
|
|
+ /*
|
|
|
+ * The pads are present but no connector is soldered on
|
|
|
+ * 2J2, so keep this off by default.
|
|
|
+ */
|
|
|
+ status = "disabled";
|
|
|
+ compatible = "composite-video-connector";
|
|
|
+
|
|
|
+ port {
|
|
|
+ cvbs_connector_in: endpoint {
|
|
|
+ remote-endpoint = <&cvbs_vdac_out>;
|
|
|
+ };
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ dc_5v: regulator-dc_5v {
|
|
|
+ compatible = "regulator-fixed";
|
|
|
+ regulator-name = "DC_5V";
|
|
|
+ regulator-min-microvolt = <5000000>;
|
|
|
+ regulator-max-microvolt = <5000000>;
|
|
|
+ regulator-always-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ emmc_pwrseq: emmc-pwrseq {
|
|
|
+ compatible = "mmc-pwrseq-emmc";
|
|
|
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
|
|
|
+ };
|
|
|
+
|
|
|
+ hdmi-connector {
|
|
|
+ compatible = "hdmi-connector";
|
|
|
+ type = "a";
|
|
|
+
|
|
|
+ port {
|
|
|
+ hdmi_connector_in: endpoint {
|
|
|
+ remote-endpoint = <&hdmi_tx_tmds_out>;
|
|
|
+ };
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ memory@0 {
|
|
|
+ device_type = "memory";
|
|
|
+ reg = <0x0 0x0 0x0 0x20000000>;
|
|
|
+ };
|
|
|
+
|
|
|
+ vcck: regulator-vcck {
|
|
|
+ compatible = "regulator-fixed";
|
|
|
+ regulator-name = "VCCK";
|
|
|
+ regulator-min-microvolt = <3300000>;
|
|
|
+ regulator-max-microvolt = <3300000>;
|
|
|
+ vin-supply = <&dc_5v>;
|
|
|
+
|
|
|
+ /*
|
|
|
+ * This is controlled by GPIOAO_9 we reserve this but
|
|
|
+ * claiming it as done below reset the board anyway
|
|
|
+ * Need to investigate this
|
|
|
+ *
|
|
|
+ * gpio = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
|
|
|
+ * enable-active-high;
|
|
|
+ */
|
|
|
+ regulator-always-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ vcc_3v3: regulator-vcc_3v3 {
|
|
|
+ compatible = "regulator-fixed";
|
|
|
+ regulator-name = "VCC_3V3";
|
|
|
+ regulator-min-microvolt = <3300000>;
|
|
|
+ regulator-max-microvolt = <3300000>;
|
|
|
+ vin-supply = <&dc_5v>;
|
|
|
+ regulator-always-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ vddio_boot: regulator-vddio_boot {
|
|
|
+ compatible = "regulator-fixed";
|
|
|
+ regulator-name = "VDDIO_BOOT";
|
|
|
+ regulator-min-microvolt = <1800000>;
|
|
|
+ regulator-max-microvolt = <1800000>;
|
|
|
+ vin-supply = <&vcc_3v3>;
|
|
|
+ regulator-always-on;
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+&cec_AO {
|
|
|
+ status = "okay";
|
|
|
+ pinctrl-0 = <&ao_cec_pins>;
|
|
|
+ pinctrl-names = "default";
|
|
|
+ hdmi-phandle = <&hdmi_tx>;
|
|
|
+};
|
|
|
+
|
|
|
+&cvbs_vdac_port {
|
|
|
+ cvbs_vdac_out: endpoint {
|
|
|
+ remote-endpoint = <&cvbs_connector_in>;
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+ðmac {
|
|
|
+ status = "okay";
|
|
|
+};
|
|
|
+
|
|
|
+&internal_phy {
|
|
|
+ pinctrl-0 = <ð_link_led_pins>, <ð_act_led_pins>;
|
|
|
+ pinctrl-names = "default";
|
|
|
+};
|
|
|
+
|
|
|
+&ir {
|
|
|
+ status = "okay";
|
|
|
+ pinctrl-0 = <&remote_input_ao_pins>;
|
|
|
+ pinctrl-names = "default";
|
|
|
+};
|
|
|
+
|
|
|
+&hdmi_tx {
|
|
|
+ status = "okay";
|
|
|
+ pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
|
|
|
+ pinctrl-names = "default";
|
|
|
+};
|
|
|
+
|
|
|
+&hdmi_tx_tmds_port {
|
|
|
+ hdmi_tx_tmds_out: endpoint {
|
|
|
+ remote-endpoint = <&hdmi_connector_in>;
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+&gpio_ao {
|
|
|
+ gpio-line-names = "UART TX",
|
|
|
+ "UART RX",
|
|
|
+ "7J1 Header Pin31",
|
|
|
+ "", "", "", "",
|
|
|
+ "IR In",
|
|
|
+ "HDMI CEC",
|
|
|
+ "5V VCCK Regulator",
|
|
|
+ /* GPIO_TEST_N */
|
|
|
+ "";
|
|
|
+};
|
|
|
+
|
|
|
+&gpio {
|
|
|
+ gpio-line-names = /* Bank GPIOZ */
|
|
|
+ "", "", "", "", "", "", "",
|
|
|
+ "", "", "", "", "", "", "",
|
|
|
+ "Eth Link LED", "Eth Activity LED",
|
|
|
+ /* Bank GPIOH */
|
|
|
+ "HDMI HPD", "HDMI SDA", "HDMI SCL",
|
|
|
+ "", "7J1 Header Pin13",
|
|
|
+ "7J1 Header Pin15",
|
|
|
+ "7J1 Header Pin7",
|
|
|
+ "7J1 Header Pin12",
|
|
|
+ "7J1 Header Pin16",
|
|
|
+ "7J1 Header Pin18",
|
|
|
+ /* Bank BOOT */
|
|
|
+ "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3",
|
|
|
+ "eMMC D4", "eMMC D5", "eMMC D6", "eMMC D7",
|
|
|
+ "eMMC Clk", "eMMC Reset", "eMMC CMD",
|
|
|
+ "SPI NOR MOSI", "SPI NOR MISO", "SPI NOR Clk",
|
|
|
+ "", "SPI NOR Chip Select",
|
|
|
+ /* Bank CARD */
|
|
|
+ "", "", "", "", "", "", "",
|
|
|
+ /* Bank GPIODV */
|
|
|
+ "", "", "", "", "", "", "", "", "", "", "", "",
|
|
|
+ "", "", "", "", "", "", "", "", "", "", "", "",
|
|
|
+ "7J1 Header Pin27", "7J1 Header Pin28", "",
|
|
|
+ "7J1 Header Pin29",
|
|
|
+ "VCCK Regulator", "VDDEE Regulator",
|
|
|
+ /* Bank GPIOX */
|
|
|
+ "7J1 Header Pin22", "7J1 Header Pin26",
|
|
|
+ "7J1 Header Pin36", "7J1 Header Pin38",
|
|
|
+ "7J1 Header Pin40", "7J1 Header Pin37",
|
|
|
+ "7J1 Header Pin33", "7J1 Header Pin35",
|
|
|
+ "7J1 Header Pin19", "7J1 Header Pin21",
|
|
|
+ "7J1 Header Pin24", "7J1 Header Pin23",
|
|
|
+ "7J1 Header Pin8", "7J1 Header Pin10",
|
|
|
+ "", "", "7J1 Header Pin32", "", "",
|
|
|
+ /* Bank GPIOCLK */
|
|
|
+ "", "";
|
|
|
+};
|
|
|
+
|
|
|
+&saradc {
|
|
|
+ status = "okay";
|
|
|
+ vref-supply = <&vddio_boot>;
|
|
|
+};
|
|
|
+
|
|
|
+/* eMMC */
|
|
|
+&sd_emmc_c {
|
|
|
+ status = "okay";
|
|
|
+ pinctrl-0 = <&emmc_pins>;
|
|
|
+ pinctrl-1 = <&emmc_clk_gate_pins>;
|
|
|
+ pinctrl-names = "default", "clk-gate";
|
|
|
+
|
|
|
+ bus-width = <8>;
|
|
|
+ cap-mmc-highspeed;
|
|
|
+ mmc-ddr-1_8v;
|
|
|
+ mmc-hs200-1_8v;
|
|
|
+ max-frequency = <200000000>;
|
|
|
+ disable-wp;
|
|
|
+
|
|
|
+ mmc-pwrseq = <&emmc_pwrseq>;
|
|
|
+ vmmc-supply = <&vcc_3v3>;
|
|
|
+ vqmmc-supply = <&vddio_boot>;
|
|
|
+};
|
|
|
+
|
|
|
+&spifc {
|
|
|
+ status = "okay";
|
|
|
+ pinctrl-0 = <&nor_pins>;
|
|
|
+ pinctrl-names = "default";
|
|
|
+
|
|
|
+ w25q32: spi-flash@0 {
|
|
|
+ #address-cells = <1>;
|
|
|
+ #size-cells = <1>;
|
|
|
+ compatible = "jedec,spi-nor";
|
|
|
+ reg = <0>;
|
|
|
+ spi-max-frequency = <3000000>;
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+&uart_AO {
|
|
|
+ status = "okay";
|
|
|
+ pinctrl-0 = <&uart_ao_a_pins>;
|
|
|
+ pinctrl-names = "default";
|
|
|
+};
|
|
|
+
|
|
|
+&usb0 {
|
|
|
+ status = "okay";
|
|
|
+};
|