Browse Source

ARM: kirkwood: SBx81LIFKW: Enable network hardware

The SBx81LIFKW boards connect to the internal chassis management network
via a Marvell 88e6097 L2 switch. The chassis connections are direct
serdes on ports 8 and 9 with a RGMII interface on port 10 connected to
the CPU MAC.

For debugging purposes ports 0 and 1 are also taken out to headers on
the board. Because the debug interfaces are sometimes connected to with
straight ribbon cables we need to run them at 10Mbps.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham 6 years ago
parent
commit
54e3316ffa

+ 12 - 2
board/alliedtelesis/SBx81LIFKW/sbx81lifkw.c

@@ -164,9 +164,15 @@ int board_init(void)
 	return 0;
 }
 
-#ifdef CONFIG_MV88E61XX_SWITCH
-/* Configure and enable Switch and PHY */
+#ifdef CONFIG_RESET_PHY_R
+/* automatically defined by kirkwood config.h */
 void reset_phy(void)
+{
+}
+#endif
+
+#ifdef CONFIG_MV88E61XX_SWITCH
+int mv88e61xx_hw_reset(struct phy_device *phydev)
 {
 	/* Ensure the 88e6097 gets at least 10ms Reset
 	 */
@@ -174,6 +180,10 @@ void reset_phy(void)
 	mdelay(20);
 	kw_gpio_set_value(MV88E6097_RESET, 1);
 	mdelay(20);
+
+	phydev->advertising = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full;
+
+	return 0;
 }
 #endif
 

+ 6 - 0
configs/SBx81LIFKW_defconfig

@@ -14,6 +14,7 @@ CONFIG_CMD_I2C=y
 CONFIG_CMD_SF=y
 CONFIG_CMD_DHCP=y
 CONFIG_BOOTP_NTPSERVER=y
+CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_SNTP=y
 CONFIG_OF_CONTROL=y
@@ -29,5 +30,10 @@ CONFIG_I2C_MUX_PCA954x=y
 CONFIG_SPI_FLASH=y
 CONFIG_SPI_FLASH_STMICRO=y
 # CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHYLIB=y
+CONFIG_MV88E61XX_SWITCH=y
+CONFIG_MV88E61XX_CPU_PORT=10
+CONFIG_MV88E61XX_PHY_PORTS=0x003
+CONFIG_MV88E61XX_FIXED_PORTS=0x300
 CONFIG_SPI=y
 CONFIG_KIRKWOOD_SPI=y

+ 0 - 5
include/configs/SBx81LIFKW.h

@@ -103,15 +103,10 @@
 #define CONFIG_NETCONSOLE	/* include NetConsole support */
 #define CONFIG_NET_MULTI	/* specify more that one ports available */
 #define CONFIG_MII		/* expose smi over miiphy interface */
-#define CONFIG_PHYLIB
 #define CONFIG_MVGBE	/* Enable kirkwood Gbe Controller Driver */
 #define CONFIG_MVGBE_PORTS	{1, 0}	/* enable a single port */
 #define CONFIG_PHY_BASE_ADR	0x01
 #define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
-#define CONFIG_RESET_PHY_R	/* use reset_phy() to init switch */
-#define CONFIG_MV88E61XX_SWITCH	/* Enable MV88E61XX switch driver */
-#define CONFIG_MV88E61XX_PHY_PORTS 0x303 /* Pt0,1,8,9 */
-#define CONFIG_MV88E61XX_CPU_PORT 10 /* 10(CPU) */
 #endif /* CONFIG_CMD_NET */
 
 /*