Explorar el Código

Cleanup use of CONFIG_SYS_SRAM_BASE and CONFIG_SYS_SRAM_SIZE

Traditionally many boards used local definitions for SRAM base address
and size (like SRAM_BASE, SRAM_LEN and/or SRAM_SIZE), while the (now)
"official" names are CONFIG_SYS_SRAM_BASE and CONFIG_SYS_SRAM_SIZE.

The corresponding code in arch/powerpc/lib/board.c was board specific,
and has never actually been maintained well. Replace this by feature-
specific code and adapt the boards that actually use this.

NOTE: there is still a ton of boards using the old #defines, which
therefor contain incorrect values in bi_sramstart and bi_sramsize.

All respective board maintainers are requested to clean up their
respective configurations.  Thanks.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Wolfgang Denk hace 14 años
padre
commit
3611665044
Se han modificado 3 ficheros con 8 adiciones y 8 borrados
  1. 3 6
      arch/powerpc/lib/board.c
  2. 3 2
      include/configs/CPC45.h
  3. 2 0
      include/configs/IP860.h

+ 3 - 6
arch/powerpc/lib/board.c

@@ -519,15 +519,12 @@ void board_init_f (ulong bootflag)
 	bd->bi_memstart  = CONFIG_SYS_SDRAM_BASE;	/* start of  DRAM memory	*/
 	bd->bi_memsize   = gd->ram_size;	/* size  of  DRAM memory in bytes */
 
-#ifdef CONFIG_IP860
-	bd->bi_sramstart = SRAM_BASE;	/* start of  SRAM memory	*/
-	bd->bi_sramsize  = SRAM_SIZE;	/* size  of  SRAM memory	*/
-#elif defined CONFIG_MPC8220
+#ifdef CONFIG_SYS_SRAM_BASE
 	bd->bi_sramstart = CONFIG_SYS_SRAM_BASE;	/* start of  SRAM memory	*/
 	bd->bi_sramsize  = CONFIG_SYS_SRAM_SIZE;	/* size  of  SRAM memory	*/
 #else
-	bd->bi_sramstart = 0;		/* FIXME */ /* start of  SRAM memory	*/
-	bd->bi_sramsize  = 0;		/* FIXME */ /* size  of  SRAM memory	*/
+	bd->bi_sramstart = 0;
+	bd->bi_sramsize  = 0;
 #endif
 
 #if defined(CONFIG_8xx) || defined(CONFIG_8260) || defined(CONFIG_5xx) || \

+ 3 - 2
include/configs/CPC45.h

@@ -347,13 +347,12 @@
 #define BOOTFLAG_WARM		0x02	/* Software reboot			*/
 
 
-#define SRAM_BASE		0x80000000	/* SRAM base address	*/
-#define SRAM_END		0x801FFFFF
 
 /*----------------------------------------------------------------------*/
 /* CPC45 Memory Map							*/
 /*----------------------------------------------------------------------*/
 #define SRAM_BASE	0x80000000	/* SRAM base address		*/
+#define SRAM_END	0x801FFFFF
 #define ST16552_A_BASE	0x80200000	/* ST16552 channel A		*/
 #define ST16552_B_BASE	0x80400000	/* ST16552 channel A		*/
 #define BCSR_BASE	0x80600000	/* board control / status registers */
@@ -361,6 +360,8 @@
 #define PCMCIA_MEM_BASE 0x83000000	/* PCMCIA memory window base	*/
 #define PCMCIA_IO_BASE	0xFE000000	/* PCMCIA IO window base	*/
 
+#define	CONFIG_SYS_SRAM_BASE	SRAM_BASE
+#define	CONFIG_SYS_SRAM_SIZE	(SRAM_END - SRAM_BASE + 1)
 
 /*---------------------------------------------------------------------*/
 /* CPC45 Control/Status Registers				       */

+ 2 - 0
include/configs/IP860.h

@@ -375,6 +375,8 @@ extern  unsigned long           ip860_get_clk_freq (void);
 #define SRAM_SIZE	(1 + (~(CONFIG_SYS_OR3 & BR_BA_MSK)))
 #define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR3			/* Make sure to map early */
 #define CONFIG_SYS_BR3_PRELIM	CONFIG_SYS_BR3			/* in case it's used for ENV */
+#define	CONFIG_SYS_SRAM_BASE	SRAM_BASE
+#define	CONFIG_SYS_SRAM_SIZE	SRAM_SIZE
 
 /*
  * BR4/OR4 - Board Control & Status (8 bit)